Close
Main Categories
    Filters
    Preferences
    Search

    Electronics & Accessories

    Electronics & Accessories

    View as Grid List
    Sort by
    Display per page

    12V 3,000 mAh NiMH Battery Pack, PP45

    #70018
    $62.02
    (1253 In stock)

    The Studica 12V 3,000 mAh NiMH (nickel metal hydride) Battery Pack, PP45 comes with a w/20 amp fuse. It is a 10-cell, 12-volt rechargeable battery that brings long-lasting power to motors and electronics that are used in the WorldSkills Mobile Robotics Collection. The Studica NiMH Battery Pack Charger, PP45, is required to charge the battery.

     

    This battery is NOT COMPETITION LEGAL for FIRST TECH CHALLENGE or FIRST ROBOTICS COMPETITION.

    Specifications,

    • Dimmensions: 5 x 2.1 x 2.1 inches (115 mm x 45 mm x 50 mm)
    • Weight: 1.32lbs (579 g)
    • Built-in 20-amp replaceable fuse for safety
    • 10-cell pack provides 3,000-mAh capacity for longer life
    • PP45 connector for easy and safe connection to controller
    • Step File

     

    6V DC Battery Holder, for Smart Robotics Servo Programmer

    #75004
    $6.88
    (4374 In stock)

    Use it to power the Studica Smart Robot Servo Programmer or any other device requiring 6V output and a TJC8 connector. 

    Specifications:

    • 6V Output
    • On/Off Power switch
    • TJC8 connector
    • Uses 4 x 1.5V AA Batteries (not included)

    Battery Clip (2 pack)

    #76088-2
    $8.96
    (543 In stock)

    Used to attach the Studica battery to the channel.

    Cobra Line Follower Sensor

    #70151
    $13.77
    (1724 In stock)

    The Cobra Line Follower Array provides 4 X QRE1113 IR reflectance sensor mounted on a 9mm pitch Each sensor is comprised of two parts - an IR emitting LED and an IR sensitive phototransistor. When you apply power to the VCC and GND pins the IR LED inside the sensor will illuminate.

    The Studica Line Sensor Board consists of 4 IR LED/phototransistor pairs, making it a great detector for a line-following robot.  The Line Sensor Board allows the robot to tell objects or surfaces apart based on how dark or light they are. It shines a beam of infrared light out onto the object, and measures how much light is reflected back.

    Each sensor provides a separate analog voltage output. The sensor board is an infrared emitter/receiver that is able to differentiate between a dark surface (with low IR reflectivity – 3.3V to 5V) and a light surface (with high IR reflectivity – 0V to 0.5V). However, this range can vary depended on the installed height of the sensor board. 

    The optimum height distance is 3-5 mm; however, the reflectivity values will change depending on distance. A daylight filter is built into the sensor.

    • 5VDC operating voltage (recommended)
    • 70mA supply current
    • Optimal sensing distance: 0.125" (3mm)
    • Step File

    Dupont Single Pin, 4 wire, female to female cable, 22AWG (2 pack)

    #71014
    $6.88
    (1113 In stock)

    Use the Dupont Single Pin - 4 wire - female to female cable with the Ultrasonic Distance Sensor

     

    Specifications: 

    • Dupont Single Pin
    • 4 wire
    • female to female cable
    • Length: 50cm
    • Gauge: 22AWG

    IR Range Sensor (10 cm to 80 cm)

    #40117
    $16.53
    (1971 In stock)

    The Sharp IR Distance Sensor GP2Y0A21YK0F uses a beam of infrared light to reflect off an object to measure its distance. Because it uses triangulation of the beam of light to calculate the distance, it is able to provide consistent and reliable readings which are less sensitive to temperature variation or the object’s reflectivity. The sensor outputs an analog voltage corresponding to the distance of the object, and can easily be read using an inexpensive analog to digital converter (ADC) chip.

    Maverick 12V DC Gear Motor w/Encoder

    #75001
    $39.96
    (3820 In stock)

    The Maverick 12V DC Gear Motor 61:1 w/Encoder was designed for strength to endure competitions, providing a stall torque of 65 min. kgf-cm.

    Specifications:

    • Voltage:                        12 volts
    • Length:                         127.5mm
    • Gear Ratios:                 61:1
    • Axel diameter:             6mm D-Shaft
    • Diameter:                     37mm
    • Stall Torque:                 65 min. kgf-cm (902 oz-in)
    • RPM:                               100
    • Encoder:                        high-resolution Hall effect, 12ppr, total count 732 per shaft rotation
    • Weight:                          0.33kgs
    • Power cable:                 PP45, 45cm, 14AWG
    • Encoder Cable:             45cm, 22AWG
    • Step File

    MD2 Motor Driver & Sensor Adapter for NI myRIO

    #71010
    $260.55
    (510 In stock)

    The MXP-MD2 is a next-generation high performance Motor Controller Driver and Sensor Adapter with many added features to make it ready to use in your robot project. The included VNH5019ATR-E Motor Controller ICs are very robust with high current output and several important protection features. Many other I/O options have been incorporated into this design to make it extremely easy to interface to several different sensors.

    Features,

    • Includes 2 VNH5019 Motor Controller ICs,
      • 2 Enable Inputs, 2 direction inputs, one PWM input per channel up to 20Khz
      • Up to 12A Continuous output per channel, 30A peak current short ms duration
      • Under-voltage, over-voltage, reverse-voltage protection
      • Thermal Shutdown protection
      • Current Limit protection
      • Current Sense Output Proportional to Motor Current (approx. 140 mV/A)
      • Loss of Ground and Loss of Vcc Protection
      • Protection against short to Ground and short to Vcc

    Specifications,

    • 3V-compatible inputs
    • Directly interfaces with myRIO MXP Port
    • 8-16V DC Battery Input Terminal, J7, (GND, MTRS+ PWR)
    • Jumper Selectable Current sense feedback from the VNH5019 Motor ICs, J12, J17
    • Reverse Power LED Indicator
    • FWD and REV Motor Direction LED Indicators
    • 3 Servo Headers, J9, J10, J11, (SIG, SVDC, GND)
    • 1 Parallax Ping Sensor Port, J13, (GND, VCC, DIO)
    • 1 Sharp IR Port, J21, (AI0, VCC, GND)
    • 1 LSB Port, J18, (VCC AI0, AI1, AI2, AI3, GND)
    • 1 NavX Port, J19, (VCC, SDA, SCL, GND)
    • 2 Encoder Ports, J22, J23, (VCC, ENCB, GND, ENCA)
    • 1 I2C Port, J20, (NC, SCL, SDA)
    • Built in 5V 3A voltage Regulator
    • 3.3V Power Rail Header, J3, from myRIO
    • 5V Power Rail Header, J4, from onboard regulator
    • GND Rail Header, J6
    • Separate Servo Power Input, J8 (SV+ PWR, GND)

    Multi-Mode Smart Servo

    #75002
    $33.07
    (2256 In stock)

    The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

    Specifications:

    Type:                             Metal Brush Motor
    Horn Gear Spline:       25T (5.9mm)
    Size:                               40mm x 20.1mm x 38.3mm
    Weight:                          65g
    Maximum Speed:        62RPM at 6V
    Stall Torque:                 20kg.cm at 6V
    Voltage:                         6-7 4V
    Cable:                             22AWG, 75cm

    MXP Extender Cable

    #69003
    $5.50
    (637 In stock)

    Extend the reach of your MXP port by using this 8 inch cable to re-position you boards where you need them.

    Features:

    • Keyed male and female 34-pin connectors
    • 28 AWG ribbon cable
    • 34 conductor
    • 8″ length

    NiMH Battery Pack Charger, PP45

    #70019
    $41.34
    (399 In stock)

    The Studica NiMH Battery Pack Charger, PP45, is used to recharge the 12V 3,000 mAh NiMH Battery Pack, PP45

    Specifications

    • Rating AC Input: 100V to 240V AC, 0.6A RMS, 50/60 Hz
    • Rating Output: 7V to 16 VDC
      • 0.9A to 1.8A
    • Protection mode: output short circuit protection and output polarity reverse protection.
    • Temperature range 0C ~+40C (battery pack)
    • Operate Humidity: 5% ~ 90%

    LED Indication

    Red Normal Main Charge mode
    Green Normal Finished / Open mode
    Red / Green Flashing Short Circuit

     

    ON/OFF Power Switch

    #62287
    $17.21
    (0 In stock)

    Studica ON/OFF Power Switch controls the power from the battery pack.

    PWM cable Set - TJC8 3 pin, 22AWG, F-F - 12 pcs

    #71011
    $22.04
    (1577 In stock)

    This set of 12 pieces includes,

    • 2 x 20cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 2 x 40cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 2 x 60cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 6 x 3pin Dupont male to male connectors

    SR-Pro 8MP Camera

    #71045
    $248.13
    (184 In stock)

    The Studica SR-Pro 8mp Camera with CSI to HDMI Adapter board was designed for the VMX-Titan Robotics Platform for WorldSkills, and Raspberry Pi hardware. 

    Features and Specifications:

    • Camera:
      • Optical Size - 1/4’’
      • Resolution - 8mp
      • Frame Rate - 1080p30, 720p60 and 640 × 480p60/90
      • Field of View (FOV) - 75 degrees (Horizontal)
      • Lens Mount - M12
      • IR Sensitivity - Visible Light Only
      • Step File
         
    • CSI-HDMI Adapter Board:
      • Supports Raspberry Pi 4B, Pi 3B+, Pi 3B, Pi 2, Model A/B/B+
      • Support Raspberry Pi 5MP OV5647/8MP IMX219/12MP IMX477 camera
      • HDMI - High Speed - 1M length
      • Reserved microphone and headphone jack for audio or GPIO signals
      • Three additional solder pads are available (same signals as headphone jack

    Titan Cable Pack

    #70162
    $9.64
    (1019 In stock)

    The Titan Cable Pack contains three cables. A 60cm CAN Wire for connecting the Titan Motor Controller to a CAN 2.0B capable device and two (idk the 50cm JST-VH to JST-VH cables for connecting 12VDC power to other devices such as the VMX or Servo Power Block.

    • 2 - JST-VH to JST-VH cable
      • 50cm
    • 1 - CAN Wire
      • 60cm

    Titan Quad Motor Controller

    #70152
    Request a Quote

    The Titan Quad Motor Controller is a powerful, 4-channel CAN-based motor controller with a built-in fuse-box (for DC motors up to 20A).

    Features:

    • 4 x Hardware encoder ports – one for each motor
    • 2 limit switch ports for each motor
    • Fuse box to set manual current limits
    • 2x Power extension ports to power other 12VDC devices. I.E.
      • VMX Robotics Controller
      • Servo Power Module
    • Built in LED Controller
    • 6A power supply for LED’s
    • i2c communication port to control LED Controller
    • USB ports are updated to USB-C to better support todays cable standards
    • Step File