Close
Menu
Main Categories
    (0) Quote
    You have no items in your shopping cart.
    (0) Items
    You have no items in your shopping cart.
    Menu
    Shopping cart
    Filters
    Preferences
    Search
    PrevCAN Bus Wire 25ft
    NextHall Effect Sensor with Har...

    Hall Effect Sensor B

    Be the first to review this product

    The best way to Hall Effect is here. Easily see when the magnet is close to this hall effect sensor with the onboard blue LED. The LED is Solid to indicate it's power and will turn off when the magnet is near.

     

    This Hall Effect is designed specifically for FIRST Robotics Competition teams. You will find this sensor being used as a limit switch in our line of DART Linear Actuators DART, 12" Actuator Kit (am-3072a) and DART, 6" Actuator Kit (am-3076a).

     

    The sensor works with either pole of the magnet and reading the sensor is easy. 5 volts means the component is safe to move 0v means the magnet is under it. You can use two for mounting and two for a cable tie to hold the connecting cable in place.

     

    Connect this sensor to your robot controller using a male PWM cable into the sensor. Black is ground, red is 5 volts, and white is signal.

    MFR Part #: am-3313b
    $16.00
    Availability: 1 in stock
    Write your own review
    • Product can be reviewed only after purchasing it
    • Only registered users can write reviews
    • Bad
    • Excellent

    Also Purchased

    Picture of 2" Compliant Wheel, 1/2 inch Hex, 50 Durometer Blue

    2" Compliant Wheel, 1/2 inch Hex, 50 Durometer Blue

    #am-3462_blue
    $8.00
    (190 In stock)

    Compliant wheels are not intended for moving robots, but moving objects. Compliant wheels give way to allow rigid objects to be manipulated easily. A line of multiple wheels on a driven hex shaft creates a very effective roller that ignores variations in the objects being driven. This makes for high-performance intakes and internal conveyors. The wheels are sized for an interference fit and tend to stay in place on a shaft, though a shaft collar may be used to make absolutely sure the wheels stay clear of other mechanisms or maintain consistent spacing.

     

    The hex bore versions of this wheel are undersized, and are intended to be an interference fit on their respective hex shafts. This interference fit allows for effective torque transfer from the hex shaft to the wheel, as well as allowing the wheel to remain in place along the shaft without the need for spacers or collar clamps:

     

    Compliant Wheel Sizing

     

    Different durometer ratings give each wheel unique characteristics. Green wheels (35A durometer) are the softest and most compliant around objects, while orange (40A), maroon (45A), and blue (50A) wheels are increasingly firm. The increased firmness also allows the latter wheels to carry a higher RPM rating. Check out the downloads tab for a chart showing wheels and their maximum RPM. 

     

     

    Specifications

     

    Customers who bought this item also bought
    Picture of 2" Compliant Wheel, 1/2 inch Hex, 50 Durometer Blue

    2" Compliant Wheel, 1/2 inch Hex, 50 Durometer Blue

    #am-3462_blue
    $8.00
    (190 In stock)

    Compliant wheels are not intended for moving robots, but moving objects. Compliant wheels give way to allow rigid objects to be manipulated easily. A line of multiple wheels on a driven hex shaft creates a very effective roller that ignores variations in the objects being driven. This makes for high-performance intakes and internal conveyors. The wheels are sized for an interference fit and tend to stay in place on a shaft, though a shaft collar may be used to make absolutely sure the wheels stay clear of other mechanisms or maintain consistent spacing.

     

    The hex bore versions of this wheel are undersized, and are intended to be an interference fit on their respective hex shafts. This interference fit allows for effective torque transfer from the hex shaft to the wheel, as well as allowing the wheel to remain in place along the shaft without the need for spacers or collar clamps:

     

    Compliant Wheel Sizing

     

    Different durometer ratings give each wheel unique characteristics. Green wheels (35A durometer) are the softest and most compliant around objects, while orange (40A), maroon (45A), and blue (50A) wheels are increasingly firm. The increased firmness also allows the latter wheels to carry a higher RPM rating. Check out the downloads tab for a chart showing wheels and their maximum RPM. 

     

     

    Specifications

     

    Information
    Customer service
    My account
    Contact Info
    Copyright © 2024 Studica Limited. All rights reserved.