JST VH 2-pin Motor Cable - 4 Pack, 50cm

• 42.0mm*42.0mm*11.3mm thick
• 16*M3*8.0mm thread
• M3 pass through holes
• SHCS sit flush
• Material - AL6061-T6

Made of aluminum, the Studica Clamping Shaft Hub is used with flex and drive wheels 

Specifcation:

• Material: 6061-T6 Aluminum
• 6mm ID
• Hole pattern for connecting to structure
• Step File 

This kit can be used in addition to the Compact Linear Slide to add an additional 12.18 inches of stroke .

Included Items:

• 1 - SAR330 Aluminum Slide (am-4837)
• 4 - 3 mm ID 12 mm OD Pulley Bearing (am-4836)
• 2 - M3-0.5 x 35 mm Socket Head Cap Screw (am-1671)
• 3 - M3-0.5 Nylock Nut (am-1023)
• 2 - M3 Female Threaded 9mm Long Hex Standoff (am-1733)
• 1 - M3-0.5 x 8mm Flat Head Cap Screw (am-1723)
• 4 - M3-0.5 x 5 mm Zinc Flat Head Cap Screw with Nylon Patch (am-1724)
• 1 - 14 inch Pulley Mount (am-5035)

Specifically designed for FTC, (though not limited to FTC), this remarkable system is a quick way to execute a controlled extension. Each stage of the Compact Linear Slide is controlled by a pulley system that can be rigged to power both extension and retraction. This is the second version of the AM Compact Linear slide, with Robits design ideals integrated. The inline stringing removes any tensioning spring requirement. The slide to pully holder attachment has been redesigned and improved.

Options:

• 1 Stage has 12.18 inches of stroke 
• 2 Stage has 24.37 inches of stroke
• 3 Stage has 36.56 inches of stroke
• Additional Stages
  • AndyMark officially supports a 3 stage system however teams may elect to add additional stages to increase reach. 
  • Load limit of 25 lbs

Suggested Rigging:

• Continuous
  • One string per direction that connects through each stage
  • For more details, see the assembly guide and video

Included Powering/Gearing:

• NeveRest Orbital 13.7 to 1:
• Speedy, approximately 1 second per stage at full speed. 
• Enough torque to easily lift multiple stages with a manipulator and game pieces
• No Motor Options have no motor included. They are compatible with NeveRest Orbital Gearmotors.
  • For lower load applications, a lower ratio gearmotor like a 3.7 or 13.7 is ideal.
  • For higher load applications, a larger ratio gearmotor like a 19.2 or 50.9 is ideal.

This is the cable designed for the encoder that is pre-attached to the NeveRest Series of motors and gearmotors. It has a connector on the opposite end to directly interface with the REV Expansion Hub or the REV Control Hub.

2019 Update:

The 'a' version of this cable as the encoder channels swapped so that the encoder counts in the same direction as the output shaft spins. This simplifies the usage of the encoder with the various programming languages for FTC!

Specifications

• Length: 20 in.

The Studica Flat Bracket is a very strong  3mm x 40mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.

Specifications:

• Material: 6061-T6 Aluminum
• Thickness - 3mm
• Width - 40mm
• Length - 192mm
• Hole Pattern - 4
• Step File

High-strength and low-stretch cord that is ideal for actuating lifts and other linear mechanisms.This cord type minimizes the need for adjustments and re-tensioning after first assembly due to its low-stretch properties.

The 2-pin JST VH Cable is keyed and locking for improved reliability. 

The Studica Servo Hub Pro can be used with the Multi Mode Servo, Multi Mode Servo 200, or most servos with a 25 Tooth gear.

Specifcations:

• Spline: 25 Tooth, 3.8mm deep
• Height: 9mm
• OD: 30mm
• Material: 6061-T6 Aluminum
• Step File

The Studica 30T Servo 25T Spline Gear is used with the Studica Multi-Mode Smart Servo or Studica Multi-Mode Smart Servo 200.

Specifications:

• Material: Steel Hardened, Zinc plated
• Step File