Close
Main Categories
    Filters
    Preferences
    Search

    Pneumatics

    Pneumatics

    View as Grid List
    Sort by
    Display per page

    Norgren Regulator and Bracket

    #am-2020
    $43.05
    (In stock)

    This is an air pressure regulator manufactured by Norgren. Also included in this part is the steel mounting bracket and a plastic mounting nut.

    Specifications:

    • Media: compressed air
    • Port Size: 1/8" NPT
    • Manufacturer: Norgren
    • Part Number: R07-100-RNEA
    • Maximum Operating (and Inlet) Pressure: 300 psi
    • Operating Temperature: -30 to 150 degrees F
    • Flow: 14.0 SCFM
    • Adjusting Knob and Bonnet Material: acetal plastic
    • Body Material: Zinc, with black powdercoat paint
    • Height: 2.91 inches
    • Depth: 1.5 inch (without gauge)
    • Weight (regulator and bracket): 0.41 pound

    Norgren relief valve

    #am-2002
    $61.50
    (In stock)

    This is a brass relief valve used in low-volume air tanks and pumps to retard excessive pressure buildup. 

    Specifications:

    • Weight: 0.11 lbs
    • Maximum operating pressure: 300 psi
    • Outlet pressure adjustment: 70-150 psi
    • Material: brass and stainless steel
    • Manufacturer: Norgren
    • Part Number: 16-004-011
    • Operating temperature range: -30 to 200 degrees F
    • Port size: 1/4" NPT

    Nylon Hex Nipple, 1/4"-1/8" NPT

    #am-2963
    $6.92
    (In stock)

    Be sure all your threaded pneumatic connections are sealed properly with this teflon tape. Standard grade PTFE tape used in all your robot pneumatics.

    Specifications:

    • Width: 1/2"
    • Length: 520"
    • Material: PTFE

    Performance Pneumatics Kit

    #am-2979
    $1295.00
    (1 In stock)

    This is the next step in a pneumatics package, which gives you all the parts you need for an entire system to push 7" stroke cylinders (included). And creates pressurized air in a safe, manageable manner for mobile robots.
     


    Entire list of Hardware:

    • One - Viair air compressor pump
    • Two - 20 meters of Pneumatic tubing, 1/4" od, polyurethane, black
    • Two - 574ml Plastic Air Tank
    • Four - Bracket for mounting Air Tank
    • Two - Valve, pneumatic, single solenoid, CKD 4GA110-M5-E01-4
    • Two - Valve, pneumatic, double solenoid, CKD 4GA120-M5-E01-4
    • Twelve - M5 Pisco Fitting for 1/4" press-in tube, POC1/4-M5
    • Two - NCME075-0700 SMC Air Cylinder, 3/4" bore, 7" stroke
    • One - Ball Valve, 1/4" NPT Male x Female, Lever Handle, Chrome Plated
    • One - Norgren pressure regulator and bracket
    • Two - Norgren pressure gauge
    • One - Norgren pressure relief valve
    • One - Nason pressure switch
    • Seven - 1/4" NPT straight press-in fitting
    • Thirteen - 1/8" NPT straight press-in fitting
    • Five - Union Tee, 1/4" tube
    • Two - 1/8 NPT Plug
    • Four - 1/8 to 1/4 NPT Nipple
    • Ten - 1/8" NPT flow control
    • Three - Bulkhead fitting
    • Thirteen - 1/8" NPT elbow press-in fitting
    • Three - PTFE Tape Roll
    • Five - 1/8" NPT Y fitting with 2 tubing ports
    • Four - Stright Y, 1/4" Tube Press-In
    • Two - 1/4 NPT Plug
    • Two - Brass Y, 1/8" NPT, 2 Female, 1 Male
    • Four - Brass Hex Nipple, 1/8" NPT
    • Two - Brass Hex Nipple, 1/4" NPT
    • Eight - Elbow, 1/4" Tube press-in, 1/4" NPT male
    • Five - Valve, 1/8 NPT, 1/4 push-in fitting
    • Three - 1/8" NPT cross fitting with 4 ports: 3 female and 1 male
    • Three - 1/4" - 1/8" NPT adapter fitting
    • Two - In-Line Flow Control, 1/4" Tube press-in

    PHD 4x4, 3/4" Bore, 4" Stroke

    #am-3304
    $49.00
    (0 In stock)

    This cylinder, manufactured by phd, Inc, is robust and features a 3/4" diameter bore and a 4" stroke. The head, cap, and tube are all made of strong, lightweight aluminum. The rod is made from chrome-plated steel, and includes standard cushions to reduce end of travel impact.

    We also provide a 2" and 6" stroke version of this same cylinder.

    Specifications:

    • Manufacturer: phd, Inc.
    • Manufacturer part number: OCG13/4x4
    • Type: Double Acting
    • Bore: 3/4"
    • Stroke: 4.0"
    • Port Size: 1/8" NPT
    • Weight: 0.42 lbs
    • Rod End Thread: 1/4-28 (NF, fine pitch)

    Pneumatic Base Kit

    #am-2000
    $395.00
    (0 In stock)

    This kit of parts makes up a system which creates pressurized air in a safe, manageable manner for mobile robots.


    This is an assortment of lightweight parts picked specifically to work well together in an efficient manner. All of these parts together weigh under 6 pounds. These parts collectively make up a pneumatic system, sending air out to the valves and cylinders. These are all of the parts you need to get controlled, pressurized air sent to your valve(s) of choice.

     

    Hardware:

    • 1 - Viair air compressor pump (am-2005)
    • 1 - 574 ml Plastic Air Tank (am-2649)
    • 2 - Bracket for mounting Air Tank (am-2008)
    • 1 - Norgren Pressure Regulator and Bracket (am-2020)
    • 2 - Pressure Gauge (am-3147)
    • 1 - Pressure Relief Valve (am-3871)
    • 1 - Nason Pressure Switch (am-2006)
    • 1 - 1/4" OD Polyurethane Pneumatic Tubing (20 yards) (am-2137)
    • 1 - 1/4" NPT straight press-in fitting (am-2010)
    • 1 - 1/8" NPT straight press-in fitting (am-2011)
    • 1 - 1/8" NPT elbow press-in fitting (am-2039)
    • 2 - 1/8" NPT flow Control (am-2897)
    • 1 - 1/8" NPT cross fitting (am-2380)
    • 1 - 1/8" NPT Y fitting (am-2183)
    • 1 - Ball Valve Fitting 1/4 in. NPT Male x Female Lever Handle (am-2023)
    • 1 - Female Fitting, 1/8" NPT, 1/4" tube (am-2033)
    • 1 - Union Tee, 1/4" tube (am-2015)
    • 1 - 1/4" x 1/8" NPT adapter fitting (am-2381)
    • 1 - Low Density PTFE Tape Roll (am-2045)

    Pneumatic Control Module

    #am-2858
    $140.00
    (In stock)

    NOTE: This product is not included in any Sales or Discounts.


    This is for the Pneumatic Control Module (aka PCM) being used in the 2015 through 2021 FIRST Robotics Competition Kit of Parts.

     

    For an overview of the 2020 Controls system, please see: https://wpilib.screenstepslive.com/s/currentCS/m/kop.

     

    The Pneumatic Control Module (aka PCM) from Cross the Road Electronics provides an easy all-in-one interface for pneumatic components.

    Pneumatic fitting, elbow, 1/4 inch tube, press-in, 1/8 inch NPT male

    #am-2039
    $3.85
    (53 In stock)

    This is a pneumatic push-to-connect male elbow fitting. The port is a 1/8" NPT male thread, and 1/4" diameter tube can be pressed in to the push-to-connect fitting. 

    Specifications:

    • Weight: 0.03 pound
    • Width: 1.05"
    • Height: 1.14"
    • Depth: 0.54"
    • Material: Brass with nickel plating, with plastic body material
    • Hex width: 1/2 inch
    • Ports: 1/8" NPT male with pre-applied PTFE thread sealant
    • Pressure range: 0-150 psi

    Pneumatic fitting, straight, 1/4 inch tube, press-in, 1/8 inch NPT male

    #am-2011
    $3.08
    (In stock)

    This is a pneumatic push-to-connect male straight fitting. The port is a 1/8" NPT male thread, and 1/4" diameter tube can be pressed in to the push-to-connect fitting. 

    Specifications:

    • Weight: 0.02 pound
    • Width: 0.53"
    • Height: 0.94"
    • Material: Brass with nickel plating
    • Hex width: 1/2 inch
    • Ports: 1/8" NPT male with pre-applied PTFE thread sealant
    • Pressure range: 0-150 psi

    Pneumatic fitting, straight, 1/4" tube, press-in, 1/4" NPT male

    #am-2010
    $3.08
    (In stock)

    This is a pneumatic push-to-connect male straight fitting. The port is a 1/4" NPT male thread, and 1/4" diameter tube can be pressed in to the push-to-connect fitting. 

    Specifications:

    • Weight: 0.03 pound
    • Width: 0.56"
    • Height: 0.93"
    • Material: Brass with nickel plating
    • Hex width: 1/2 inch
    • Ports: 1/4" NPT male with pre-applied PTFE thread sealant
    • Pressure range: 0-150 psi

    Pneumatic fitting, union tee, 1/4" tube

    #am-2015
    $5.00
    (In stock)

    This is a pneumatic push-to-connect union tee fitting. All three of the ports are push-to-connect 1/4" fittings.

    Specifications:

    • Weight: 0.02 pounds
    • Width: 1.66"
    • Height: 1.10"
    • Depth: 0.525"
    • Material: Plastic body
    • Ports: 1/4" push-to-connect fitting
    • Pressure range: 0-150 psi

    Pneumatic Fittings Kit

    #am-2678
    $375.00
    (0 In stock)

    This pneumatic fittings kit is perfect for your first time using pneumatics or restocking your current supply. It contains many of the most commonly used fittings as well as a few extras that always come in handy when re-configuring or repairing.



    Individual Components within this Bundle:

    • four - straight, 1/4" press-in to 1/4" NPT
    • six - straight, 1/4" press-in to 1/8" NPT
    • twelve - elbow, flow control, 1/4" press-in, 1/8" NPT
    • twelve - elbow, 1/4" press-in, 1/8" NPT
    • four - union tee, three port 1/4" press-in
    • two - 1/8" NPT hex head plug
    • four - 1/4" - 1/8" NPT, hex nipple
    • two - 1/8" NPT to 1/4"press-in, female bulkhead
    • four - 1/8" NPT hex nipple
    • two - 1/2" x 520"PTFE tape roll
    • eight - elbow, 1/4" press-in to 1/4" NPT
    • two - union tee, 1/8" NPT, 2 female mooports, 1 male port
    • two - 1/4" NPT hex nipple
    • two - 1/4" NPT hex head plug
    • four - 1/4" press-in, Y
    • four - 1/4" press-in (two), 1/8" NPT (one), Y
    • two - cross, 1/8" NPT, 3 female ports, 1 male port
    • two - 1/8" NPT male to 1/4" NPT female
    • two - Flow Control, In-Line, 1/4" tube, press-in
    • four - 1/8" NPT, 1/4" push-in, valve

    Pneumatic Reservoir Bracket

    #am-2008
    $4.50
    (In stock)

    This is a plastic bracket for mounting the Clippard Air Tank (am-2649).

    If you plan to use this bracket to hold of these am-2649 tanks, we recommend using two brackets for each tank. 

    Specifications:

    • Weight: 0.066 pound
    • Width: 3.14 inches
    • Height: 2.65 inches
    • Thickness: 0.75 inch
    • Material: Plastic

    For Pro Charging Systems, warranty replacements contact Richard Harmon. 

    Pressure Gauge with 1/8 in. NPT Fitting

    #AM-4222
    $26.00
    (In stock)

    This is a miniature pressure gauge with 1/8 in. NPT threads perfect for lightweight pneumatic systems where you need to mount a pressure gauge to a hard fitting. This pressure gauge is significantly reduced in volume and weight compared to the classic gauges used in FRC. This lets you take advantage of every last cubic inch and ounce on your robot.

     

    Specifications

    • Height: 0.83 in
    • Operating Pressure: 0-150 psi
    • Port(s): 1/8 in. NPT
    • Pressure Range : 0-116 psi
    • Width: 0.59 in

    Pressure Gauge with Male 1/4 in. Press-in fitting

    #am-4225
    $36.75
    (In stock)

    This is a miniature pressure gauge with a male 1/4 in. push to connect fitting making it easy to install in any of our push to connect fittings to get exactily the layout you are looking for. It can even be installed in the end of one of our air tanks where you might usually put a plug. This pressure gauge is significantly reduced in volume and weight compared to the classic gauges used in FRC. This lets you take advantage of every last cubic inch and ounce on your robot.

     

    Specifications

    • Height: 1.5 in
    • Operating Pressure: 0-150 psi
    • Port(s): 1/4 in. Male Push In
    • Pressure Range: 0-116 psi
    • Width: 0.59 in

     

    Pressure Guage, 1/8 inch NPT, 0-160 PSI

    #am-3147
    $19.00
    (In stock)

    This pneumatic pressure gauge features a 1/8" NPT male fitting. This part is used to read the overall pressure for your pneumatic system.

    Specifications:

    • Weight: 0.144
    • Width: 1.5" Diameter Face
    • Total length: 1.5"
    • Wrench needed for installation:
    • Face color: White with Black Lettering
    • Manufacturer: Marsh
    • Capacity: 0-160 PSI
    • Port:1/4" Male NPT