Pressure Relief Valve, Soft Seat Safety, 125 psi, 62 SCFM, 1/8 in. Port

This is a brass adapter fitting with a male 1/8" NPT thread and a female 1/4" NPT port.

This fitting helps out an application when a device with a 1/4" NPT male thread needs to fit into a 1/8" NPT female port.

Specifications:

• Weight: 0.05 lbs
• Length: 0.91 inch
• Hex width: 0.67 inch, turned with a 11/16 wrench
• Material: Brass with nickel plating
• Ports: 1/8" NPT male, 1/4" NPT female
• Pressure rating: 230 psi

This is a Nickel plated Brass cross union with three (3) Female connections with 1/8 NPT thread and one (1) male connection at 1/8 NPT.

This part can replace heavier brass manifold pieces and makes your pneumatic system lighter.

Specifications:

• Weight: 0.08 lbs
• Width: 1.65 in
• Height: 0.51 in
• Depth: 1.58 in
• Material: Brass with nickel plating
• Ports: 3 Female 1/8 NPT, 1 male 1/8 NPT
• Pressure rating: 230 psi

This is a handy cable to connect the 120 amp breaker to the Power Distribution Panel. The cable is made of 6 gauge multi-strand wire while the connectors are securely crimped and protected with heat shrink tubing. The tip-to-tip length is approximately 5 inches. This cable is used in the Robot Power Cable Kit. Both end connectors of cable are crimped with a 6-ton pneumatic linkage crimping tool. 

Specifications:

• Gauge: 6
• Weight: 0.3 pounds
• Overall Length: Approximately 7 in.

Included Hardware: 

• One - 6 gauge multistrand (50 strands) wire, red @ ~5"
• Two - Molex crimp connectors w/ 1/4" diameter ring (2)
• Two - Blue heat shrinks over Molex connecto

VIAIR 90C compressor (air pump) offers a light duty solution for smaller air requirements. These compact compressors and are meant to fill no larger than a 1.0 gallon air tank. 

VIAIR part number 00090

Specifications:

• Manufacturer: VIAIR Corporation
• Weight: 2.4 pounds
• Width: 2.11 inches
• Height: 4.53 inches
• Length: 5.94 inches
• Material: Steel and aluminum
• Manufacturer: Viair Corporation
• Part Number: 00090
• Flow Rate: 0.88 cfm at 0 ps
• Ports: 1/8" NPT
• Voltage: 12 Volt DC
• Permanent Magnet Motor
• Duty Cycle: 9% @ 100 psi
• Maximum Working Pressure: 120 psi
• Maximum Amp Draw: 11 amps

Hardware: 

• Vibration Isolators (4)
• Screw (4)
• Nut (4)
• Washer (8)
• Lock Washer (4)

Fill Rate

• This pump will take approximately 13 seconds to fill one (1) plastic Clippard tank (574 ml) from 0 to 120 psi.

Products to be used on:

• Mobile Robots
• Outdoor equipment

For VIAIR compressor warranty replacements contact Ryan Shaw.

• Phone: 949-585-0011 x110
• Email: [email protected]

This is a handy cable, positioned on a robot, to connect the Power Distribution Panel to a battery. The cable is made of 6 gauge multistrand wire while the connectors are securely crimped and protected with heat shrink tubing. The tip-to-tip length is approximately 20 inches. Also, this cable is used in the Robot Power Cable Kit. Both end connectors of each cable are crimped with a 6-ton crimping tool.

Specifications:

• Gauge: 6
• Weight: 0.35 pounds
• Length: Approximately 20 inches
• Connector Type: Anderson Powerpole SB50

Included Hardware:

• One - SB-50A Anderson Power Products connector
• One - 6 gauge multistrand (50 strands) wire, red @ ~11"
• One - 6 gauge multistrand (50 strands) wire, black@ ~18"
• Two - Molex crimp connectors w/ 1/4" diameter ring (2)
• Two - Blue heat shrinks over Molex connector

Do you have a hard time finding some strong hex stock aluminum? We have it! This is 7075 series aluminum, which is great for use in transmission shafts.

Specifications:

• Material: 7075 Aluminum
• Width: 1/2" hex (0.496-0.499 inches)
• Weight: 0.27 pounds/ft
• Length: You specify, 1 foot, 3 feet or 6 foot in length, +/- 1"

This is a Nickel plated Brass "Y" union with two (2) Female connections with 1/8 NPT thread and one (1) male connection at 1/8 NPT.

Specifications:

• Weight: 0.05 lbs
• Width: 1.54 in
• Height: 0.51 in
• Depth: 1.09 in
• Material: Brass with nickel plating
• Ports: 2 Female 1/8 NPT, 1 male 1/8 NPT
• Pressure range: 0-250 psi