Close
Main Categories
    Filters
    Preferences
    Search

    U-Channel Bumper (4 pack)

    The Studica U-Channel Bumper is connected to the end of the Studica 48mm U-Channel and helps remove sharp corners that can cause damage when the robot is bumping into other objects. It also creates an ecstatically clean finish to your robot.

    Specifications:

    MFR Part #: 76505-4
    $9.85
    In stock

    Write your own review
    • Product can be reviewed only after purchasing it
    • Only registered users can write reviews
    *
    *
    • Bad
    • Excellent

    Customers who bought this item also bought

    6mm D-Shaft Low Profile Clamping Hub

    #76292
    $8.44
    ( 830 In stock)

     

     

    Φ29.0mm*16.0mm thick
    6*M3 thread tapping through
    (including 2*M3 thread for M3 SHCS)
    Φ6.0mm D hole
    AL6061-T6

    Servo Arm

    #76151
    $7.73
    (In stock)

    The Studica Servo Arm can be used with the Multi Mode Servo, Multi Mode Servo 200, or most servos with a 25 Tooth gear.

     

    Specifcations:

    • Spline: 25 Tooth, 3.8mm deep
    • Length: 33mm
    • Width: 14mm
    • Height: 7.8mm
    • Material: 6061-T6 Aluminum
    • Step File

    Multi-Mode Smart Servo

    #75002
    $41.15
    ( 191 In stock)

    The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

     

    Programming the Smart Servo using the Smart Servo Programmer

     

    CAD File

     

    Clamping Hub 6mm D-Shaft - v2

    #76280
    $11.10
    ( 1710 In stock)

    Made of aluminum, the Studica Clamping Shaft Hub is used with flex and drive wheels 

    Specifcation:

    • Material: 6061-T6 Aluminum
    • 6mm ID
    • Hole pattern for connecting to structure
    • Step File 

    6mm D-shaft Intake Hub Kit

    #70210
    $11.25
    ( 733 In stock)

    The Intake Kit can be used to create intake systems and is ideal for the FIRST Technical Challenge (FTC) and World Robotics Olympiad (WRO). Used with the Silicone Rubber Tubing #76410


    Specifications:

    • Main piece
      • hex width: 20.78mm*10.0mm thick
      • 6*M6 tapped holes
      • 1*M4 tappped hole for M4 set screw
      • 6.0mm Diameter D Hole
      • Material AL6061-T6
      • Φ7.5mm*14.0mm
    • Pins
      • 6PCS in a pack
      • M6*4.0mm thread
      • Material SS303
    • Step file

    Servo Hub Pro

    #76152
    $7.73
    (In stock)

    The Studica Servo Hub Pro can be used with the Multi Mode Servo, Multi Mode Servo 200, or most servos with a 25 Tooth gear.

     

    Specifcations:

    • Spline: 25 Tooth, 3.8mm deep
    • Height: 9mm
    • OD: 30mm
    • Material: 6061-T6 Aluminum
    • Step File

    Face Bearing Block

    #76299
    $14.07
    ( 240 In stock)

    The Studica Face Bearing Block can be mounted on any  Studica channel and bracket providing which will allow for a 6mm ID through hole for 6mm shafts (axles). It has a permanently installed Standard Sealed Bearing. Has 8 x M3 tapped through holes for easy mounting.

    Motor Mount Clamp Kit

    #76141
    $15.48
    ( 829 In stock)

    Use the Motor Mount Clamp kit when fastening motors on body and attaching kit to channel and other structure.