0.125 in. Thick 31.5 in. x 23.5 in. Perforated Polycarbonate Sheet

Must be ordered in mulitples of 25

Specifications:

• Material: Steel
• Coating: Zinc plated
• Thread: 1/4-20
• Width across hex: 7/16"

1/2 inch external retaining ring, used in the RAW Box. 

Specifications: 

• Material: Steel
• For Shaft Diameter: 1/2"
• Thickness: 0.031"
• Type: External Retaining Ring
• Free Inside Diameter: 0.456"
• Plier Hole Diameter: 0.40"
• Weight: 0.002 pounds

The Bumper Wood Corner Bracket is designed to connect two plywood planks together to form a strong 90 degree bumper corner.

Specifications

• Material: 5052 Aluminum

Documents

Layout Print(s)

am-3233 AM14U3 Bumper Outside Corner Bracket.PDF

CAD File(s)

am-3233 AM14U3 Bumper Corner Bracket.STEP

This is a Heavy Duty Hex Bearing which outperforms our previous 1/2" Hex Bearings as it has a Heavy Duty Inner Race. This FR8ZZ-HexHD bearing, 1/2" hex bore, flanged, heavy duty inner race, shielded ball bearing, has an inner race that is thicker and stronger than our recent offering of a similar bearing (am-0279). This bearing has more material between the corners of the hex bore and the edge of the race making it stronger and much less likely to crack under high load.

This bearing is guaranteed to have a stronger, thicker race. 100% of these bearings have been quality checked for a smooth fit over 1/2" hex stock here at AndyMark. Many of our long-time customers will recognize this bearing, as it is the same version we sold back in 2008-2011, and we did not have any failures. Now, it is renamed and quality checked for your high load needs - including drive chassis with cantilevered wheels.

Specifications:

• Inside diameter: 0.500-0.502 inch hex bore
• Outside diameter: 1.125 inch
• Flange thickness: 0.062 inch
• Overall thickness: 0.312 inch
• Weight: 0.05 pound

These custom designed collar clamps have been designed specifically with FIRST Robotics Competition teams in mind. The one-piece collar clamp is a nice fractional 1/2 in. width to make shaft stackups easy. The clamping force is provided by a 10-32 socket head screw, which is bigger than most used in the competition marketplace.  This provides a high-strength clamping solution that shouldn't strip out when you need it most. You can even replace the 10-32 screw if it becomes lost with the screws historically used in the AM14U family of chassis. These thoughtfully designed collar clamps also have small bosses on each side. This allows these collar clamps to be installed directly adjacent to an FR8ZZ Round or FR8ZZ Hex bearing without rubbing on the outer races for smooth operation.

The MINI® Fuse is the standard for vehicle circuit protection. Its miniature design meets the need for more circuits to be protected while utilizing less space, and its ability to cope with high temperatures in adverse environments makes the MINI® Fuse of recommended choice for protection.

This mini fuse can be used in our Power Pole Distribution Board (am-3699), as well as a replacement in the Power Distribution Panel (am-2856)

This novel style of collar clamp is split into two pieces so that it can be attached without removing any shafts. The bore is a 1/2" hex. The flats on the perimeter allow for the collar clamp to be held in position or turned for better assembly control. 

This clamp has been designed and fabricated by BaneBots, and proudly sold through AndyMark.

Specifications:

• Material: Aluminum
• Bore: hex hole, 1/2 inch
• Outside Diameter: 0.94 inch
• Thickness: 0.375 inch
• Width Across Flats: 7/8 inch
• Weight: 0.020 pound
• Clamping Screws: #6-32 x 1/2" long (qty. 2)

Plastic spacers are included with this clamp, positioned between the two halves. These are to be removed before usage.