Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    10mm Key Hub

    This is a 10mm Key Hub. This hub fits all AndyMark wheels. 

    The machine key is not included with the hub.

    Specifications:

    • Material: 6061 Aluminum
    • Bore: 10mm (0.374 inch), with a 4mm (0.157 inch) keyway
    • Bolt Pattern: Six - 0.204" diameter holes, evenly spread on a 1.875" diameter bolt circle.
    • Finish: tumbled
    • Outside diameter: 2.25 inches
    • Weight: 0.11 pound
    # Pièce: am-0985a
    $16.91
    Disponibilité: En stock

     

    Écrivez votre propre commentaire
    • Le produit peut être examinée que après l'achat
    • Seul les utilisateurs enregistrés peuvent écrire une critique
    • Mal
    • Excellent

     

    Les clients ayant acheté cet article ont également acheté

    20 AWG White Ferrule Crimps

    #am-3738_20
    $0.10

    6 Gauge Compression Lug Connector 1/4 Stud Hole BURNDY #: YAZV6CTC14FX

    #am-0805
    $5.50
    (256 En stock)

    This is a heavy-duty compression lug from BURNDY for 06 AWG wire. This compression log can be easily crimped with the Cable Lug Crimping Tool.

     

    Specifications

    • Gauge: 06 AWG
    • Hole Size For Stud: 0.25 in.
    • Material: Copper
    • Overall Length: 2.03 in.
    • Tongue Width: 0.48 in.
    • Weight: 0.01 lbs
    • Wire Strip Length: 1.18 in.

    20 Amp MINI Yellow Fuse

    #am-3605
    $1.50
    (En stock)

    This 20 Amp fuse is used in FIRST Tech Challenge batteries and the FIRST Robotics Competition Power Distribution Panel (am-2856).

    Specifications:

    • Color: Yellow
    • Amps: 20
    • Max Voltage: 32
    • Style: MINI®
    • Specification: SAE J2077
    • Type: Blade Fuse

    6" DuraOmni Wheel with 1/2" Bearings

    #am-3290
    $59.96
    (En stock)

    This Heavy Duty (HD) omni wheel is a vast improvement over our older 6" omni wheels and other wheels on the market. The body has been totally redesigned with durability and mobility in mind. The design intent is to provide a smooth roll along with the ability to handle impacts very well.

    The body is made from black polycarbonate, while the rollers are each molded with a nylon core and TPU tread. These rollers spin smoothly on a captured dowel pin.

    Specifications: 

    • Diameter: 6 inches
    • Width Across Middle:
    • Bore: 1.125 inch diameter x 0.36" deep with a 0.96" diameter thru hole
    • Bolt Pattern: 6 holes (0.157 in.) on a 1.875 inch bolt circle
    • Body Material: Black polycarbonate
    • Load Capacity: 120 pounds
    • Weight: 1 Pound
    • Number of Rollers: 10
    • Roller Material, Outside: Gray TPU rubber
    • Roller Durometer: 77A
    • Roller Material, Inside: white nylon
    • Roller Bearing Material: nylon spinning on steel
    • Roller Axle: 1/8" diameter steel dowel pin
    • Assembled and Repairable by installing or removing 10-24 screws
    • Half inch id bearings pre-pressed into hub

    Individual Components within this Part:

    • One - Interior polycarbonate body piece
    • Two - Outer polycarbonate body pieces
    • Ten - Rollers
    • Ten - Steel Dowel Pins
    • Ten - Thread Forming Screws
    • Two - 1/2" id Bearing, Shielded (R8ZZ) (am-0181)

    Short 1/2" Hex Steel Output Shaft for Toughbox Series

    #am-0802
    $13.84
    (En stock)
    This is the optional HEX STEEL output shaft for the Toughbox gearbox. This is the same as the Short 1/2 in. Hex Aluminum Output Shaft with Magnet for Toughbox® Series Gearboxes (am-0397a), but made of steel rather than aluminum.

    Vinyl Stick-on Number, White, 4 inch tall, Qty 4 - "7"

    #AM-2687
    $9.00
    (En stock)

    This is a package of FOUR stick-on numbers, designed to be adhered to robot bumper material.

    Specifications:

    • Quantity: 4
    • Material: White stick-on plastic
    • Height: 4 inches
    • Width: 2.6 inches
    • Line width: 0.8 inch
    • Weight: 0.004 pounds

    Usage (for best application):

    • Apply heat to cloth area using a heat gun or hairdryer for 30 seconds (prior to placing number). Do not put heat on or near pool noodles, as they will shrink.
    • Place numbers in position on bumper material as desired with pressure.
    • Apply heat to numbers using a heat gun or hairdryer for 30 seconds.
    • Place under a static load for 5 minutes.