Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    57 Sport Gearbox 100:1 HD Ratio

    The 57 Sport is a competition tested high performance line of planetary gearboxes from AndyMark and BaneBots. The 57 Sport features numerous improvements over previous planetary gearboxes used on FIRST Robotics Competition robots. 

    # Pièce: am-4006_100
    $159.00
    Disponibilité: Rupture de stock - en rupture de stock et sera expédié une fois en stock.

    The cold formed steel gears inside this gearbox are a 0.7 Module tooth profile which is 40% larger than the vast majority of planetary gearbox gears previously used on competition robots. The gears are larger, but the housing's size has been optimized to reduce any unnecessary volume. This means you get more reliability without sacrificing precious space. This housing is also one solid piece of aluminium, ensuring that there is no possibility for misalignment of the stages during assembly or during the rigors of match play. 

    Three stage, and now optionally two stage, versions of these gearboxes also feature an "HD" stage, with gears approximately double the face width of the other stages as well as a strengthened carrier plate. These larger gears on the output stage ensure that it will handle heavy or cantilevered loads without worry. The carrier plates are made of hardened 4140 steel and interface to the output shaft with a robust hex bore. New for 2019 we are opening up the use of every available gear ratio with every available motor input meaning there are some combinations that could theoretically exceed the gearboxes design characteristics. As such the blanket warranty we offered on these gearboxes in the past will be discontinued for future purchases. Rest assured that AndyMark still stands behind our product 100% and if you feel that there is a problem with your gearbox or any of our products please contact us and we will make it right. To help you decide which gearboxes to use for your application please reference the below table which includes the maximum torque that the gearbox is designed to take before it will fail.

    A free packet of red tacky grease (am-2768) is included with every gearbox purchased. This grease must be used to coat every internal surface of the gearbox before use. 

    The 57 Sport includes mounting hardware for any 500 or 700 series motor including the AndyMark RedLine, the VexPro 775pro, the AndyMark RS775-5, the BaneBots RS775, the BaneBots RS550, and the AndyMark NeveRest. To install one of these motors, first remove any installed pinion from the motor and press on the included pinion gear using an arbor press or bench vice. This press fit ensures a solid mechanical connection between the pinion gear and the motor. This pinion assembly is not susceptible to vibration and never needs to be checked once installed. All ratios of Blue Sport Gearboxes use a 4:1 input stage, with the same tooth count pinion, so motors and gearboxes can be switched out with ease.

     

    Part Number Ratio Weight Length Stall Torque* Rated Torque Free Speed*
    am-4005_004 4:1 SD 0.76 lb 2.62 in. 1.8 ft-lbs 120 ft-lbs 4910 rpm
    am-4005_012 12:1 SD 0.97 lb 3.42 in. 5.5 ft-lbs 135 ft-lbs 1630 rpm
    am-4006_012 12:1 HD 1.06 lb 3.67 in. 5.5 ft-lbs 170 ft-lbs 1630 rpm
    am-4005_016 16:1 SD 0.98 lb 3.42 in. 7.4 ft-lbs 120 ft-lbs 1220 rpm
    am-4006_016 16:1 HD 1.07 lb 3.67 in. 7.4 ft-lbs 160 ft-lbs 1220 rpm
    am-4005_020 20:1 SD 0.98 lb 3.42 in. 9.2 ft-lbs 110 ft-lbs 980 rpm
    am-4006_020 20:1 HD 1.08 lb 3.67 in. 9.2 ft-lbs 140 ft-lbs 980 rpm
    am-4006_036 36:1 HD 1.27 lb 4.17 in. 16.6 ft-lbs 170 ft-lbs 540 rpm
    am-4006_048 48:1 HD 1.30 lb 4.17 in. 22.2 ft-lbs 170 ft-lbs 400 rpm
    am-4006_064 64:1 HD 1.28 lb 4.17 in. 29.6 ft-lbs 160 ft-lbs 300 rpm
    am-4006_080 80:1 HD 1.30 lb 4.17 in. 37.0 ft-lbs 140 ft-lbs 240 rpm
    am-4006_100 100:1 HD 1.30 lb 4.17 in. 46.2 ft-lbs 140 ft-lbs 190 rpm

    Common Physical Specifications:

    Mounting Features:
    • Four 10-32 0.25 in. deep tapped holes on a 1/2 in. by 1 in. or 1 in. square grid, on two oppisite faces
    Output Shaft Geometry:
    • 0.5 in. Hex Profile
    • 1.0 in. Length

    *Theoretical maximum values when paired with an AndyMark 775 RedLine Motor (am-3775)
    Écrivez votre propre commentaire
    • Le produit peut être examinée que après l'achat
    • Seul les utilisateurs enregistrés peuvent écrire une critique
    • Mal
    • Excellent

    The cold formed steel gears inside this gearbox are a 0.7 Module tooth profile which is 40% larger than the vast majority of planetary gearbox gears previously used on competition robots. The gears are larger, but the housing's size has been optimized to reduce any unnecessary volume. This means you get more reliability without sacrificing precious space. This housing is also one solid piece of aluminium, ensuring that there is no possibility for misalignment of the stages during assembly or during the rigors of match play. 

    Three stage, and now optionally two stage, versions of these gearboxes also feature an "HD" stage, with gears approximately double the face width of the other stages as well as a strengthened carrier plate. These larger gears on the output stage ensure that it will handle heavy or cantilevered loads without worry. The carrier plates are made of hardened 4140 steel and interface to the output shaft with a robust hex bore. New for 2019 we are opening up the use of every available gear ratio with every available motor input meaning there are some combinations that could theoretically exceed the gearboxes design characteristics. As such the blanket warranty we offered on these gearboxes in the past will be discontinued for future purchases. Rest assured that AndyMark still stands behind our product 100% and if you feel that there is a problem with your gearbox or any of our products please contact us and we will make it right. To help you decide which gearboxes to use for your application please reference the below table which includes the maximum torque that the gearbox is designed to take before it will fail.

    A free packet of red tacky grease (am-2768) is included with every gearbox purchased. This grease must be used to coat every internal surface of the gearbox before use. 

    The 57 Sport includes mounting hardware for any 500 or 700 series motor including the AndyMark RedLine, the VexPro 775pro, the AndyMark RS775-5, the BaneBots RS775, the BaneBots RS550, and the AndyMark NeveRest. To install one of these motors, first remove any installed pinion from the motor and press on the included pinion gear using an arbor press or bench vice. This press fit ensures a solid mechanical connection between the pinion gear and the motor. This pinion assembly is not susceptible to vibration and never needs to be checked once installed. All ratios of Blue Sport Gearboxes use a 4:1 input stage, with the same tooth count pinion, so motors and gearboxes can be switched out with ease.

     

    Part Number Ratio Weight Length Stall Torque* Rated Torque Free Speed*
    am-4005_004 4:1 SD 0.76 lb 2.62 in. 1.8 ft-lbs 120 ft-lbs 4910 rpm
    am-4005_012 12:1 SD 0.97 lb 3.42 in. 5.5 ft-lbs 135 ft-lbs 1630 rpm
    am-4006_012 12:1 HD 1.06 lb 3.67 in. 5.5 ft-lbs 170 ft-lbs 1630 rpm
    am-4005_016 16:1 SD 0.98 lb 3.42 in. 7.4 ft-lbs 120 ft-lbs 1220 rpm
    am-4006_016 16:1 HD 1.07 lb 3.67 in. 7.4 ft-lbs 160 ft-lbs 1220 rpm
    am-4005_020 20:1 SD 0.98 lb 3.42 in. 9.2 ft-lbs 110 ft-lbs 980 rpm
    am-4006_020 20:1 HD 1.08 lb 3.67 in. 9.2 ft-lbs 140 ft-lbs 980 rpm
    am-4006_036 36:1 HD 1.27 lb 4.17 in. 16.6 ft-lbs 170 ft-lbs 540 rpm
    am-4006_048 48:1 HD 1.30 lb 4.17 in. 22.2 ft-lbs 170 ft-lbs 400 rpm
    am-4006_064 64:1 HD 1.28 lb 4.17 in. 29.6 ft-lbs 160 ft-lbs 300 rpm
    am-4006_080 80:1 HD 1.30 lb 4.17 in. 37.0 ft-lbs 140 ft-lbs 240 rpm
    am-4006_100 100:1 HD 1.30 lb 4.17 in. 46.2 ft-lbs 140 ft-lbs 190 rpm

    Common Physical Specifications:

    Mounting Features:
    • Four 10-32 0.25 in. deep tapped holes on a 1/2 in. by 1 in. or 1 in. square grid, on two oppisite faces
    Output Shaft Geometry:
    • 0.5 in. Hex Profile
    • 1.0 in. Length

    *Theoretical maximum values when paired with an AndyMark 775 RedLine Motor (am-3775)
    Les clients ayant acheté cet article ont également acheté

    Collar Clamp, 1/2 Hex Bore, 2 Pc with Flats

    #am-2871
    $12.68
    (12 En stock)

    This novel style of collar clamp is split into two pieces so that it can be attached without removing any shafts. The bore is a 1/2" hex. The flats on the perimeter allow for the collar clamp to be held in position or turned for better assembly control. 

    This clamp has been designed and fabricated by BaneBots, and proudly sold through AndyMark.

    Specifications:

    • Material: Aluminum
    • Bore: hex hole, 1/2 inch
    • Outside Diameter: 0.94 inch
    • Thickness: 0.375 inch
    • Width Across Flats: 7/8 inch
    • Weight: 0.020 pound
    • Clamping Screws: #6-32 x 1/2" long (qty. 2)

    Plastic spacers are included with this clamp, positioned between the two halves. These are to be removed before usage.

    0.50 in. Hex and Keyed Shaft Coupling

    #AM-1560
    $25.00
    (15 En stock)

    Whether you have shafts that are too short or shafts of different types, this coupling will solve every component connection issue you've had! Need to combine multiple hex shafts, multiple 1/2-inch keyed shafts, or convert between hex and keyed? This coupling solves all at a better price than anyone else can offer!

    Shaft Compatability

    This coupling has geometry to capture 0.50-inch hex shafts with an inside hex of 0.51 to 0.52 inches as well as 0.5 inch keyed shafts with a 1/8th inch keyway with a keyway width of 0.128 inches to 0.131 inches.

    60 Tooth 9 mm Wide 5 mm Pitch HTD Timing Belts - Gates

    #am-4659
    $16.95
    (17 En stock)

    These are all of our 9 mm wide 5 mm pitch HTD synchronous timing belt offerings. All of these belts are a composite of flexible rubber with a fiberglass tensile member throughout. Synchronous timing belts, also known as a toothed belt or synchronous belt, are designed to eliminate slippage and keep any number of objects rotating at a constant rate. We offer both genuine Gates brand belts as well as lower-cost generic brand belts. 

     

    Current Belt Offerings

     

    Parts are organized by the following scheme: (Tooth Count - Trade Number - AndyMark part number)

     

    Gates Brand Belts

    • 48T - 240-5M-09 - am-3274
    • 60T - 300-5M-09 - am-4659

     

    Generic Brand Belts

    • 40T - 200-5M-09 - am-3272
    • 45T - 225-5M-09 - am-3273
    • 48T - 240-5M-09 - am-3662
    • 70T - 350-5M-09 - am-4359
    • 93T - 465-5M-09 - am-3378

    Generic 9 mm Wide 5 mm Pitch HTD Timing Belt 150 Tooth

    #am-4911
    $19.00
    (18 En stock)

    These are all of our 9 mm wide 5 mm pitch HTD synchronous timing belt offerings. All of these belts are a composite of flexible rubber with a fiberglass tensile member throughout. Synchronous timing belts, also known as a toothed belt or synchronous belt, are designed to eliminate slippage and keep any number of objects rotating at a constant rate. We offer both genuine Gates brand belts as well as lower-cost generic brand belts. 

     

    Standard 20DP Gears 1/2 in Hex, 36 Tooth

    #am-4709
    $22.00
    (27 En stock)

    20 DP gears are the most common gears used in FIRST Robotics Competition gearboxes. Want to replace one of your existing gears? Building a custom gearbox? This page is a hub for all of our standard width, symmetrical 3/8 hex and 1/2 inch hex bore 20 DP gears.

    Check out our other 20 DP Gear pages for Pinion Gears and Shifting Gears and other special gears like those for the Toughbox line.

    Passive Power Over Ethernet Injector

    #am-3766
    $16.00
    (En stock)

    Have you lost OpenMesh Radio power during a match because the barrel came unplugged? You can keep that from happening ever again by using this Power Over Ethernet (POE) injector. This injector inserts POE power to a CAT5 Ethernet data cable on the unused Ethernet pins 4,5(+) and 7,8(-) allowing you to stop the worry about the barrel connector failures.
     

    The barrel connector will still need to be used but it can move to a more secure location that can be wrapped with electrical tape to keep it in place better than attempting to tape it to the back of the OpenMesh Radio.
     

    Plug in the RJ-45 of this unit to your roboRIO, plug the same 12V barrel connector from your Voltage Regulator Module (VRM) into the power port, securely tape it in place with electrical tape (better than awkwardly to the back to the OpenMesh Radio), and run an Ethernet cable from the female port to the Ethernet port closes to the power input on your OpenMesh Radio.

     

    Specifications

    • Length: 9.5 in.

     

    Documents

    Guide(s)

    am-3766 Using the POE Injector.pdf