Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Accessoires FTC

    Hardware

    Voir comme Grille Lister
    Trier par
    Affichage par page

    F6 Flexible 1/2" Self-Wrap Split Braided Sleeving, 10ft section

    #am-2602
    $15,38 $17,36
    (En stock)

    F6's unique split, semi-rigid braided construction makes it the ideal solution for situations where ease of installation is of primary importance. The lateral split allows the tube to open up to accommodate a wide variety of bundling requirements, and the semi-rigid braid configuration simply closes around the entire installation without the need for any additional fasteners (velcro, tape, etc.) The 10 mil PET braid is lightweight, quiet and flexible. The 25% edge overlap (at nominal diameter) allows coverage around inline plugs, connectors and splices. F6 will bend to a tight radius without distorting or splitting open and, unlike full rigid tubing, will not impair or affect the flexibility of harnesses.

    Urethane Belt Joining Kit, 110V

    #76401
    $280,28 $276,43
    ( 12 En stock)

    This kit includes the tools need to cut and join a urethane belt. Recommended for the 5mm Urethane Round Belt - part # 76400

    Urethane Belt Joining Kit, 220V

    #76402
    $280,28 $276,43
    ( 32 En stock)

    This kit includes the tools need to cut and join a urethane belt. Recommended for the 5mm Urethane Round Belt - part # 76400

    6 in 1 Screwdriver

    #70141
    $8,44 $8,32
    ( 237 En stock)

    Includes 6 bits,

    • Slotted 3.3
    • Phillips: OHO
    • Hex 1/16inch
    • Hex 3/32inch
    • Hex 7/64inch

    M3 T-Slot Nut (100 pack)

    #76130
    $5,62 $5,54
    ( 981 En stock)

    The M3 T-Slot Nut 100 pack, is a Hammer Head Series 20 and is used with any M3 screw and fits the Studica T-Slot Extrusions.

     

    Powerpole Crimp Tool 15/30/45

    #70143
    $39,00 $52,77
    ( 69 En stock)

    This crimp tool is the ultimate Powerpole crimper. The jaws work for 15, 30, and 45 connectors. This crimp tool has a built-in positioner to hold the contacts during crimping. The ratchet mechanism assures proper crimps every time.

     

    The 15 amp connector and be crimped with 16 28 and 20 AWG wire. The 30 amp connector can be crimped with 12 and 14 AWG wire. 45 amp connector can be crimped with 10-12 AWG wire.

    2.5mm Hex Ball End Screwdriver

    #70142
    $8,44 $8,32
    ( 1987 En stock)
    • Used with M3 screws

    Chain Breaker Tool

    #76231
    $29,00 $41,66
    ( 37 En stock)

    The easy way to change the length of your #25 chain. (Chain not included)

    Combination Wrench, 5.5mm

    #70145
    $9,85 $9,71
    ( 362 En stock)

    M3 Kep Nut (100 pack)

    #76204-100
    $14,07 $13,88
    ( 2991 En stock)

    M3 Nyloc Nut (100 pack)

    #76205-100
    $12,66 $12,49
    ( 3680 En stock)

    M3 x 10mm Button Head Cap Screw (50 pack)

    #76203-50
    $12,66 $12,49
    ( 3473 En stock)

    M3 x 10mm Button Head Cap Screw (pack of 50), Zinc Plated.

    M3 x 10mm Socket Head Cap Screw (100 pack)

    #76201-100
    $19,00 $18,74
    ( 3520 En stock)

    M3 x 10mm Socket Head Cap Screw (pack of 100), Zinc Plated.

    M3 x 12mm Socket Head Cap Screw (100 pack)

    #76202-100
    $20,13 $19,85
    ( 866 En stock)

    M3 x 12mm Socket Head Cap Screw (pack of 100), Zinc Plated.

    M3 x 20mm Socket Head Cap Screw (50 pack)

    #76209-50
    $11,25 $11,10
    ( 780 En stock)

    M3 x 20mm Socket Head Cap Screw (pack of 50), Zinc Plated.

    M3 x 30mm Socket Head Cap Screw (50 pack)

    #76206-50
    $11,68 $11,52
    ( 3167 En stock)

    M3 x 30mm Socket Head Cap Screw (pack of 50), Zinc Plated.

    M3 x 8mm Socket Head Cap Screw (100 pack)

    #76200-100
    $18,30 $18,04
    ( 1151 En stock)

    M3 x 8mm Socket Head Cap Screw (pack of 100), Zinc Plated.

    M3 x 4mm Set Screw (10 pack)

    #76210-10
    $7,03 $6,93
    ( 0 En stock)

     

    Spare sets screws for Studica Robotics Hubs and Collars

     

    10 Pack CONE HEX SOCKET SET SCREW DIN 914 M3 Thread

    • 3 mm Long
    • 1.5 mm Hex Socket
    • 2 mm Socket Depth

     

    M4 x 6mm Set Screw (10 pack)

    #76211-10
    $7,03 $6,93
    ( 2 En stock)

    Spare sets screws for Studica Gears Including:

    76219 - 30 Tooth Bevel Gear

     

    10 Pack CONE HEX SOCKET SET SCREW DIN 914 M4 Thread

    • 6 mm Long
    • 2 mm Hex Socket
    • 2 mm Socket Depth

    Hex Key Metric 7 Piece Set (1.5, 2, 2.5, 3, 4, 5, 6)

    #70144-7
    $14,07 $13,88
    ( 1164 En stock)

    Specifications:

    • 7 color pcs
    • 1.5, 2, 2.5, 3, 4, 5, 6
    • Non-slip handle
    • ball-end and straight-end
    • S2 Hardness
    • Non-corrosive
    • Weight: 0.118kg

    Rubber Grommet (10 pack)

    #76504-10
    $8,44 $8,32
    (En stock)

    Rubber Grommets are made for the Studica channel and plates and or any structure with a 14mm hole. Use it for protecting wire or as a bumper.

    Specifications:

    • Outside diameter: 18mm
    • Inside Diameter : 11mm
    • Hole fitting diameter: 14mm
    • Thickness: 9mm
    • Step File

    U-Channel Bumper (4 pack)

    #76505-4
    $9,85 $9,71
    (En stock)

    The Studica U-Channel Bumper is connected to the end of the Studica 48mm U-Channel and helps remove sharp corners that can cause damage when the robot is bumping into other objects. It also creates an ecstatically clean finish to your robot.

    Specifications:

    Rubber Foot (4 pack)

    #76506-4
    $7,73 $7,63
    (En stock)

    Made of Nylon, the Studica Rubber Foot is used with the Studica Robotics building structure and for many other uses.

    M3 x 10mm Low Profile Screw with Kep Nut (6 pack)

    #76199-6
    $4,21 $4,15
    ( 2342 En stock)

    The M3 x 10mm Low Profile Screw with Kep Nut is a 304 Stainless Steel m3 Din 7991 Countersunk Hex Socket Flat Head Screw with a matching Kep Nut. This package is made for the Slide Rail, 288mm Length, 180mm Stroke and the Slide Rail, 384mm Length, 240mm Stroke

    Includes,

    • 6 - M3 x 10mm Low Profile Screw
    • 6 - Kep nut

    Toolbox in Black

    #70056
    $27,99

    Specifications:

    • 61cm x 38cm x 33cm
    • Black
    • Heavy duty
    • Volume: 53 Liters
    • Padlock tabs for added security
    • Durable design
    • Reinforced removable lid
    • Molded grooves for easy and sturdy stacking

    M3 x 25mm Socket Head Cap Screw (pack of 50)

    #76214-50
    $11,25 $11,10
    ( 887 En stock)

    M3 x 25mm Socket Head Cap Screw (pack of 100), Zinc Plated.

    M3 x 6mm Socket Head Cap Screw (pack of 50)

    #76213-50
    $8,44 $8,32
    ( 993 En stock)

    M3 x 6mm Socket Head Cap Screw (pack of 50), Zinc Plated.

    Step file

    Solid Carbide Spiral End Mill For Arcylic-One Flute (XSTECH)

    #Dd4-25-D4-50L-HRC50
    $13,99 $13,88
    ( 0 En stock)
    MaterialTungsten Carbide
    FluteSingle Flute Spiral End Mill
    CoatingDLC Rainbow
    Shank Diameter4 mm

    iCrimp Ferrule Crimping Tool Kit

    #HSC86-4+E-770
    $32,99
    ( 56 En stock)

    iCrimp Ferrule Crimping Tool Kit, AWG 23-10 Self-adjustable Ratchet Ferrule Crimper Plier c/w 770End Sleeve Ferrules Connector Terminals

    iCrimp Cable Lug Crimping Tool

    #HX-50BI
    $34,00
    ( 50 En stock)

    iCrimp Cable Lug Crimping Tool for Heavy Duty Wire Lugs,Battery Terminal,Copper Lugs AWG 8-1/0

     

    •  6 dies in AWG: 8,6,4,2,1,1/0
    •  Hexagonal rotating dies are processed with Wire EDM Cutting, more accurate than normal casting dies.
    •  Comfortable grip with antislip surface saves strength and improves user’s experience.
    •  Made of high quality carbon steel which can offer long service life.
    • Compatiable with copper&aluminum cable lug,non-welding and standard electrical connection.

     

    ICrimp Insulated Terminal Ratchet Wire Crimping Tool Kit

    #IWS-03C+KIT285
    $35,70 $34,71
    ( 50 En stock)
    iCrimp Insulated Terminal Crimping Tools Ratchet Wire Crimper with 285pcs Insulated Butt, Spades, Rings Connectors from AWG22-10

    iCrimp Open Barrel Crimper

    #IWS-2412M
    $22,99
    ( 10 En stock)
    iCrimp Open Barrel Crimping Tools Works on AWG24-12 JAM, Molex, Tyco, JST Terminals and Connectors

     

    Purpose: IWS-2412M open barrel crimper tool is designed to crimp non-insulated open barrel, OEM-style terminals. Perfect for servo lead connectors and some other RC crimp connectors.

     

    iCrimp Mini Micro Open Barrel Crimper

    #IWS-2820M
    $23,99
    ( 9 En stock)
    iCrimp Mini Micro Open Barrel Crimping Tools Works on AWG28-20 JAM, Molex, Tyco, JST Terminals and Connectors

     

    IWS-2820M open barrel crimper tool is designed to crimp non-insulated open barrel, OEM-style terminals. Perfect for servo lead connectors and some other RC crimp connectors.

    5.5mm Nut Driver

    #70146
    $8,44 $8,32
    • For 5.5mm nuts
    • CRV material
    • heat treatment
    • surface matt chrome plated
    • 100mm exposure shank
    • socket head cold heading treatment

    5.5mm Combination Ratchet Wrench

    #70147
    $14,07 $13,88
    • Used with 5.5mm Nuts
    • 50BV30 ratchet head
    • heat treatment
    • surface balck finished
    • body #45 carbon steel material
    • mirror polishing
    • product engrave size and laser logo
    • length 110mm

    Silicone Rubber Tubing

    #76410
    $5,62 $5,54

    Used with the Intake Kit to create various intake system with various lengths.

    • ID: 6mm
    • OD: 10mm
    • 1000mm long
    • Wall Thickness: 2mm
    • Flexible
    • Bend Radius: ~30mm
    • Silicone
    • Durometer: 70A
    • Black
    • Step File