Blue Nitrile Roughtop Tread 1.5 in. Wide 10 ft. Long

This is a heavy-duty compression lug from BURNDY for 06 AWG wire. This compression log can be easily crimped with the Cable Lug Crimping Tool.

Specifications

• Gauge: 06 AWG
• Hole Size For Stud: 0.25 in.
• Material: Copper
• Overall Length: 2.03 in.
• Tongue Width: 0.48 in.
• Weight: 0.01 lbs
• Wire Strip Length: 1.18 in.

This is 12 GA bonded wire* with Red and Black Jacketing. It is much easier to use than two separate wires, easier to follow during troubleshooting, and easier to keep your wiring clean. Pull apart at the end only as much as you need and the rest stays together.

If you are looking for a much more flexible wire or wire that is not bonded check out our Silicone Wire. 
 

* - This is also known as zip cord or zip wire.

Specifications

• Gauge: 12 AWG
• Length: 25 feet
• Total Weight: 1.2 lbs
• Weight: 0.05 lbs/ft
• Wire Jacketing: black & red (bonded together)

This is a plastic air tank accumulator holding 574 ml, manufactured by Clippard.

This black plastic tank has been improved over the last white plastic design from Clippard. Each end now has molded in plastic push-in fittings. These eliminate the need to have metal fittings to be screwed in to the tank, and omits the uncertainty of over-tightening a fitting into the tank.

Specifications:

• Manufacturer: Clippard
• Weight: 0.64 lbs
• Capacity: 574 ml (35 cu. inch)
• Ports: Two 1/4" od tube push-in fittings
• Maximum pressure: 125 psig
• Temperature rating: 35 to 100 F
• Length: 12.25"
• Diameter: 2.5" (@ main tank), 2.75" max

A mounting bracket is available to order (am-2008), but is not included when ordering just this item.

Note: If you have received a faulty air tank (damaged push to connect fittings) please contact Scott Lamb of Clippard Technical Sales at (513)-521-4445 (ext 1213).

This novel style of collar clamp is split into two pieces so that it can be attached without removing any shafts. The bore is a 1/2" hex. The flats on the perimeter allow for the collar clamp to be held in position or turned for better assembly control. 

This clamp has been designed and fabricated by BaneBots, and proudly sold through AndyMark.

Specifications:

• Material: Aluminum
• Bore: hex hole, 1/2 inch
• Outside Diameter: 0.94 inch
• Thickness: 0.375 inch
• Width Across Flats: 7/8 inch
• Weight: 0.020 pound
• Clamping Screws: #6-32 x 1/2" long (qty. 2)

Plastic spacers are included with this clamp, positioned between the two halves. These are to be removed before usage.

Every millimeter counts in electrical installations: Building technology requires more and more functions integrated into ever smaller spaces. This connector accommodate fine-stranded wires from 0.14 to 4 mm2 (24–12 AWG), as well as solid and stranded wires from 0.2 to 4 mm2 (24–12 AWG). This wide range allows you to connect different types of wires and enables bridging of wires with greatly differing cross sections.

The SRX Mag Encoder is a rotary sensor that can be used to measure rotational position and velocity. The device senses the magnetic field of a diametrically polarized magnet to determine rotational position with 12 bit precision. The device provides both a Quadrature interface that may be used for relative position measurement and a Pulse Width Modulated output for absolute position measurement. The device connects directly to the Talon SRX data port and is directly supported in the Talon SRX firmware. Please see Magnetic Encoder user's guide for more information and kit contents.

Works with this cable:
Talon SRX Data Cable, 6 in (am-2617)

Included Components:

• 1 - Clear ABS Housing
• 1 - Magnet
• 2 - 3-48 Housing Screws
• 1 - 2-28 x 7/16" Screw
• 1 - Encoder

This is a 25 foot section of a twisted pair of 22 AWG wire.

Specifications

• Gauge: 22 AWG
• Length: 25 feet

These double acting single rod stainless steel cylinders are a solid choice when you want air actuated motion. These cylinders have a strong 0.75 in. thick bore and are available in multiple stroke lengths.

These double acting single rod stainless steel cylinders are a solid choice when you want air actuated motion. These cylinders have a strong 0.75 in. thick bore and are available in multiple stroke lengths.

RED Cordura nylon bumper fabric material. Each piece is 161 x 19.5 inches, enough to cover the entire perimeter of your FRC robot. The material is heavy-duty nylon cloth, much like the material used on backpacks.

 

Additional Information:
 

We also have stick-on numbers available (not included with the material).

Specifications

• Color: Red
• Denier: 1000
• Length: 161 in.
• Material: Nylon
• Width: 19.5 in.