Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    6mm Hex-Shaft Clamping Shaft Hub

    The Studica Robotics Clamping 6mm Hex-Shaft Hub is used with flex and drive wheels and is improved for the absolute strongest hold.

    # Pièce: 76281H
    $11,58
    Les clients ayant acheté cet article ont également acheté

    2" Compliant Wheel, 1/2 inch Hex, 35 Durometer Green

    #am-3462_green
    $9,50
    ( 27 En stock)

    Compliant wheels are not intended for moving robots, but moving objects. Compliant wheels give way to allow rigid objects to be manipulated easily. A line of multiple wheels on a driven hex shaft creates a very effective roller that ignores variations in the objects being driven. This makes for high-performance intakes and internal conveyors. The wheels are sized for an interference fit and tend to stay in place on a shaft, though a shaft collar may be used to make absolutely sure the wheels stay clear of other mechanisms or maintain consistent spacing.

     

    The hex bore versions of this wheel are undersized, and are intended to be an interference fit on their respective hex shafts. This interference fit allows for effective torque transfer from the hex shaft to the wheel, as well as allowing the wheel to remain in place along the shaft without the need for spacers or collar clamps:

     

    Compliant Wheel Sizing

     

    Different durometer ratings give each wheel unique characteristics. Green wheels (35A durometer) are the softest and most compliant around objects, while orange (40A), maroon (45A), and blue (50A) wheels are increasingly firm. The increased firmness also allows the latter wheels to carry a higher RPM rating. Check out the downloads tab for a chart showing wheels and their maximum RPM. 

     

     

    Specifications

     

    • Bore: 1/2 in. Hex, 3/8 in. Hex, Nub Bore
    • Diameter: 2 in.
    • Durometer: 35A (Green), ⠀40A (Orange), ⠀45A (Maroon), ⠀50A (Blue), 60A (Black)
    • Hole Pattern: Qty 2 3.5 mm Holes on a 16 mm Circle for 8 mm bore wheels
    • Material: TPU
    • Maximum RPM: 6000 - 9000
    • Weight: 0.035 lb.
    • Width: 0.5 in.

     

    Documents

    Layout Print(s)

    am-3571 2IN 375 Hex Compliant Wheel REV3.PDF

    am-3462 2IN 500Hex Compliant Wheel REV3.PDF

    am-3572 2IN 8mm Compliant Wheel REV4.PDF

    CAD File(s)

    am-3571 2IN 375Hex Compliant Wheel REV2.STEP

    am-3572 2IN 8mm Compliant Wheel REV2.STEP

    am-3462 2IN Molded 500Hex Compliant Wheel REV2.STEP

    Additional File(s)

    2 inch Compliant Wheel Expansion.pdf

    Don't see what you need?

    2" Compliant Wheel, 1/2 inch Hex, 40 Durometer Orange

    #am-3462_orange
    $9,25
    ( 58 En stock)

    Compliant wheels are not intended for moving robots, but moving objects. Compliant wheels give way to allow rigid objects to be manipulated easily. A line of multiple wheels on a driven hex shaft creates a very effective roller that ignores variations in the objects being driven. This makes for high-performance intakes and internal conveyors. The wheels are sized for an interference fit and tend to stay in place on a shaft, though a shaft collar may be used to make absolutely sure the wheels stay clear of other mechanisms or maintain consistent spacing.

     

    The hex bore versions of this wheel are undersized, and are intended to be an interference fit on their respective hex shafts. This interference fit allows for effective torque transfer from the hex shaft to the wheel, as well as allowing the wheel to remain in place along the shaft without the need for spacers or collar clamps:

     

    Compliant Wheel Sizing

     

    Different durometer ratings give each wheel unique characteristics. Green wheels (35A durometer) are the softest and most compliant around objects, while orange (40A), maroon (45A), and blue (50A) wheels are increasingly firm. The increased firmness also allows the latter wheels to carry a higher RPM rating. Check out the downloads tab for a chart showing wheels and their maximum RPM. 

     

    Specifications

    • Bore: 1/2 in. Hex, 3/8 in. Hex, Nub Bore
    • Diameter: 2 in.
    • Durometer: 35A (Green), ⠀40A (Orange), ⠀45A (Maroon), ⠀50A (Blue), 60A (Black)
    • Hole Pattern: Qty 2 3.5 mm Holes on a 16 mm Circle for 8 mm bore wheels
    • Material: TPU
    • Maximum RPM: 6000 - 9000
    • Weight: 0.035 lb.
    • Width: 0.5 in.

     

    Documents

     

    Layout Print(s)

    am-3571 2IN 375 Hex Compliant Wheel REV3.PDF

    am-3462 2IN 500Hex Compliant Wheel REV3.PDF

    am-3572 2IN 8mm Compliant Wheel REV4.PDF

    CAD File(s)

    am-3571 2IN 375Hex Compliant Wheel REV2.STEP

    am-3572 2IN 8mm Compliant Wheel REV2.STEP

    am-3462 2IN Molded 500Hex Compliant Wheel REV2.STEP

    Additional File(s)

    2 inch Compliant Wheel Expansion.pdf

    GT2-6mm Smooth Idler Pulley, H Type, w/3mm Inner Bore Bearing

    #76455
    $9,85
    ( 1533 En stock)

    GT2-6mm Smooth Idler Pulley, H Type, w/3mm Inner Bore Bearing

    2.25 inch Compliant Wheel, 1/2 inch Hex, 50A Durometer, Blue

    #am-3949_blue
    $10,00 $10,42
    ( 55 En stock)

    Compliant wheels are not intended for moving robots, but moving objects. Compliant wheels give way to allow rigid objects to be manipulated easily. A line of multiple wheels on a driven hex axle creates a very effective roller that ignores variations in the objects being driven. This makes for high-performance intakes and internal conveyors.



    Different durometer ratings give each wheel unique characteristics. Green wheels (35A durometer) are the softest and most compliant around objects, maroon (45A), blue (50A), and black (60A) wheels are increasingly firm. The increased firmness also allows the latter wheels to carry a higher RPM rating. Check out the downloads tab for a chart showing wheels and their maximum RPM.

     

    Specifications

     

    • Bore: 0.375 in. Hex, 0.50 in. Hex, 5 mm Hex
    • Core Material: Polycarbonate
    • Diameter: 2.25 in.
    • Durometer: 35A (Green), 40A (Orange), 50A (Blue), 60A (Black)
    • Tread Material: TPU
    • Weight: 0.08 lbs
    • Width: 1 in.

     

    Documents

    Layout Print(s)

    am-3949 2.25IN 500Hex HD Compliant Wheel REV3.PDF

    am-3950 2.25IN 375Hex HD Compliant Wheel REV3.PDF

    am-4536 2.25in HD 5mm Hex Molded Compliant Wheel.PDF

    CAD File(s)

    am-3949 2.25IN 500Hex HD Compliant Wheel.STEP

    am-3950 2.25IN 375Hex HD Compliant Wheel.STEP

    am-4536 2IN OverMolded 5mm Hex Compliant Wheel.STEP

    GT2-6mm Timing Belt Clamp w/Set Screw

    #76456
    $7,03
    ( 807 En stock)

    The GT2-6mm Timing Belt Clamp w/Set Screw is used with all the GT2 belts

    Specifications:

    6mm Hex-Shaft Shaft Coupling ID x 12mm OD (2 pack)

    #76303H-2
    $7,23
    (En stock)

    The Studica Robotics Hex-Shaft Coupling has an ID of 6mm and an OD of 12mm.  It can be used with the 6mm Hex-Shaft Axle and a 6mm shaft DC motor. 

    6mm Hex-Shaft Nylon Spacer 1mm (24 pack)

    #76305H-24
    $8,68

    This Studica Robotics 1mm nylon spacer 24-pack is used to space gears, sprockets, wheels, and other parts along a 6mm Hex-shaft. Mix and match with various spacer lengths.

    6mm Hex-Shaft Low Profile Clamping Hub

    #76292H
    $8,68
    (En stock)

    The Studica Robotics 6mm Hex-Shaft Low Profile Clamping Hub is an ideal fit for our motors.