Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Entretoises et rondelles

    Entretoises et rondelles
    Voir comme Grille Lister
    Trier par
    Affichage par page

    Aluminum Spacer 1.1 in.

    #am-2920
    $3.08
    (En stock)

    1.1" Long Aluminum Spacer. Used in the Swerve and Steer.

    Specifications:

    • Length: 1.1 in.
    • Outside diameter: 0.31 in.
    • Inside diameter: 0.26 in.
    • Material: 6061 Aluminum
    • Weight: 0.002 Pounds
    •  

    AM Shifter Cylinder Plate

    #am-2263
    $9.23
    (En stock)

    This is to mount a pneumatic cylinder to your Shifters.

    Specifications:

    • Material: Aluminum
    • Thickness: 0.29"
    • Weight: 0.025 pounds

    AM Shifter Spacer

    #am-2264
    $4.61
    (En stock)

    2.6" long aluminum spacer used in the AM Shifter

    Specifications:

    • Length: 2.6"
    • Outside diameter: 0.5"
    • Inside diameter: 0.26"
    • Material: 6061 Aluminum
    • Weight: 0.04 Lb

    Arm Joint Spacer

    #am-2693
    $12.30
    (En stock)

    The Spacer used in the PVC Arm Joint

    Specifications:

    • Length: 5"
    • Thickness: 0.1 in
    • Height: 2.375"
    • Weight: 0.12 lbs
    • Material: aluminium

    Bushing, Bronze, 5/16" id, 0.50" od, 0.50" long

    #am-2698
    $3.08
    (En stock)

    This is the bronze bushing (and spacer!) used in the Worm Gearbox (am-0917).

    Specifications:

    • Weight: 0.013 pounds
    • Material: Bronze
    • Inside Diameter: 5/16"
    • Outside Diameter: 0.5"
    • Length: 0.5"

    CIM Spacer 125

    #am-2223
    $7.69
    (En stock)

    This nifty 1/8" thick spacer is for mounting CIM motors to gearboxes which may need clearance for protruding bearings or other things that are in the way.

    Specifications:

    • Material: Aluminum
    • Thickness: 0.125"
    • Weight: 0.014 Lbs

    CIM Sport Side Mount Spacer

    #am-3786
    $11.54
    (En stock)

    This spacer attaches to a side of the CIM Sport Gearbox. This spacer accounts for the difference in size between the CIM Motor and the gearbox housing, allowing the gearbox to be side mounted to a surface. The holes are sized to be counterbore for 10-32 socket head screws so the plate can be held to the gearbox with some screws and used as a spacer for other longer bolts to pass through it and thread into the side of the CIM Sport. 

    Specifications:

    • Width: 1.5 in.
    • Height: 1.5 in.
    • Thickness: 0.33 in.
    • Material: Aluminum
    • Weight: 0.058 Pounds

    Hex Molded Spacers 3/8 inch Hex, 0.063 inch length

    #am-3947-063
    (En stock)
    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8" and 1/2" hex bores to accommodate the most common shaft types. If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! These spacers are molded in black polycarbonate, a tough, crack resistant material that FIRST teams are familiar with. These spacers should resist stress cracking. If polycarbonate isn't rugged enough for your high load application or you need custom length spacers, check out our Aluminum Hex Spacer Extrusion.

    Hex Molded Spacers 3/8 inch Hex, 0.125 inch length

    #am-3947-125
    $0.92
    (En stock)
    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8" and 1/2" hex bores to accommodate the most common shaft types. If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! These spacers are molded in black polycarbonate, a tough, crack resistant material that FIRST teams are familiar with. These spacers should resist stress cracking. If polycarbonate isn't rugged enough for your high load application or you need custom length spacers, check out our Aluminum Hex Spacer Extrusion.

    Hex Molded Spacers 3/8 inch Hex, 0.188 inch length

    #am-3947-188
    $0.92
    (En stock)
    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8" and 1/2" hex bores to accommodate the most common shaft types. If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! These spacers are molded in black polycarbonate, a tough, crack resistant material that FIRST teams are familiar with. These spacers should resist stress cracking. If polycarbonate isn't rugged enough for your high load application or you need custom length spacers, check out our Aluminum Hex Spacer Extrusion.

    Hex Molded Spacers 3/8 inch Hex, 0.250 inch length

    #am-3947-250
    $0.92
    (En stock)
    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8" and 1/2" hex bores to accommodate the most common shaft types. If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! These spacers are molded in black polycarbonate, a tough, crack resistant material that FIRST teams are familiar with. These spacers should resist stress cracking. If polycarbonate isn't rugged enough for your high load application or you need custom length spacers, check out our Aluminum Hex Spacer Extrusion.

    Hex Molded Spacers 3/8 inch Hex, 0.5 inch length

    #am-3947-500
    $0.92
    (En stock)
    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8" and 1/2" hex bores to accommodate the most common shaft types. If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! These spacers are molded in black polycarbonate, a tough, crack resistant material that FIRST teams are familiar with. These spacers should resist stress cracking. If polycarbonate isn't rugged enough for your high load application or you need custom length spacers, check out our Aluminum Hex Spacer Extrusion.

    Hex Molded Spacers 3/8 inch Hex, 1 inch length

    #am-3947-1000
    $0.99
    (En stock)

    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8" and 1/2" hex bores to accommodate the most common shaft types. If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! These spacers are molded in black polycarbonate, a tough, crack resistant material that FIRST teams are familiar with. These spacers should resist stress cracking. If polycarbonate isn't rugged enough for your high load application or you need custom length spacers, check out our Aluminum Hex Spacer Extrusion.

    Hex Spacer 0.570 inchL x 0.5 inchID Hex x 1.124 inch OD

    #am-1305
    $5.39
    (En stock)

    This unique spacer can be used to support a wheel on a 1/2" hex shaft. It presses into a bearing bore and centers the hex shaft.

    Specifications: 

    • Material: Polypropylene Plastic
    • Length: 0.57 inch
    • OD: 1.125 inch
    • ID: 0.505 inch Hex
    • Weight: 0.013 pound

    Nylon Roller for 2x1 Elevator

    #am-1449
    $1.54
    (En stock)

    This nylon roller is used within our 2x1 Single Stage Elevator Bearing and Structure Kit (am-3844).

    Specifications:

    • Material: Nylon
    • ID: 0.26 in.
    • OD: 0.75 in.
    • Length: 1.0 in.
    • Weight: 0.016 Pounds

    PicoBox Spacer

    #am-3406
    $2.31
    (En stock)

    Used to properly space the plates in the PicoBox series of gearboxes.


    Specifications:

    • Length: 1.169"
    • Outer Diameter: 0.375"
    • Inner Diameter: 0.261"
    • Weight: .02 Lb
    • Material: 6061 Aluminium