A better way to Hall Effect is here. Now you can easily see when the magnet is close to this hall effect sensor as there is a blue LED, on to know it's powered, that will turn off when the magnet is near. This Hall Effect is designed specifically for FRC use and is featured in the DART, Sensor Kit (am-3077) for the DART, 12" Actuator Kit (am-3072a) and DART, 6" Actuator Kit (am-3076a). The sensor works with either pole of the magnet and reading the sensor is easy, 5v means component is safe to move 0v means the magnet is under it. This hall effect sensor board has four mounting holes. You can use two for mounting and two for a cable tie to hold the connecting cable in place. Features:
Dimensions:
The Studica Light Weight Shaft Hub is used with the 6mm D shafts. It has a 5mm set screw for tight clamping and seven M3 tapped mounting holes.
Specifcation:
Our Entrapption Stars have two bore options, making them viable parts for both FRC and FTC! This product is frequently used as intake wheels for picking up game pieces. Made from silicone, they are flexible, yet firm, allowing for the ability to pick up objects of irregular shape.
The 1/2 in. Hex Bore option is designed to be an interference fit on any 0.5 in. Hex Shaft. This means the bore is actually 0.425 in. and it will be a tight press on, but keep the entrapption star from rotating.
Used with Studica Omni and Mecanum wheels for a strong axel hold.
Specifications:
This 0.5 in. long 8-32 Button Head Cap Screw is used on the end of a Falcon 500 motor to retain pinions, adapters, or other spline hardware. It is included with the Falcon 500 Spline to 1/2 inch Hex Shaft Adapter.
The Motor Mount Plate is used with the Maverick 12V DC Gear Motor (Part# 75001) to attach it inside the anyone of the U Channels 76010 to 76018. This is an example of a chassis with 4 motors mounted inside the U-Channel using a Motor Mounting Plate.
Used to change motor to axle motion 90 degrees. This can be used in between the U-channel.
The Studica End Piece Plate is commonly fastened to the inside end of the U Channel. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
This simple bracket handles so many of your mounting needs! Mount motors or gearboxes anywhere and make axle supports with bearings - it's a do-it-all, put-it-anywhere bearing and motor mount bracket.
Any motor or gearbox with a 2-inch diameter bolt circle can be mounted in this bracket. The center hole is sized to hold a standard 1.125 inch outside diameter bearing.
Examples of motors with a 2 in. diameter bolt circle:
Examples of gearboxes with a 2 in. diameter bolt circle
Layout Print(s)
am-4244 1IN Pitch Bent Motor and Bearing Bracket REV2.PDF
CAD File(s)
am-4244 1IN Bent Bearing Side Mount Gusset.STEP
This is 12 GA bonded wire* with Red and Black Jacketing. It is much easier to use than two separate wires, easier to follow during troubleshooting, and easier to keep your wiring clean. Pull apart at the end only as much as you need and the rest stays together.
If you are looking for a much more flexible wire or wire that is not bonded check out our Silicone Wire.
* - This is also known as zip cord or zip wire.
This is 18 AWG (gauge) bonded wire* with Red and Black Jacketing. It is much easier to use than two separate wires, easier to follow during troubleshooting, and easier to keep your wiring clean. Pull apart at the end only as much as you need and the rest stays together.