Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Hex Molded Spacers, 1/2 Hex, .063 Thick

    These spacers are molded in black polycarbonate, a tough, crack resistant material that FIRST teams are familiar with. These spacers should resist stress cracking. If polycarbonate isn't rugged enough for your high load application or you need custom length spacers, check out our Aluminum Hex Spacer Extrusion.

    # Pièce: am-3948-063
    $0,90
    Disponibilité: 101 en stock

    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8", 1/2", and 5 mm hex bores to accommodate the most common shaft types They can also be used on round shafts and bolts (5mm is great for #10 hardware!). If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! 

    Specifications

    • Inside Diameter: 0.375 in. Hex, 0.50 in. Hex, 5 mm Hex
    • Length: 0.063 in., 0.125 in., 0.188 in., 0.250 in., 0.375 in., 0.50 in., 1.00 in.
    • Material: Polycarbonate
    • Outside Diameter: 0.787 in. Round
    • Weight: Up to 0.014 lbs

    Documents

    Layout Print(s)

    am-3947 375IN Hex Molded Spacers Layout REV4.PDF

    am-3948 500IN Hex Molded Spacers Layout REV4.PDF

    am-4535 5mm Hex Molded Spacers Layout.PDF

    Écrivez votre propre commentaire
    • Le produit peut être examinée que après l'achat
    • Seul les utilisateurs enregistrés peuvent écrire une critique
    *
    *
    • Mal
    • Excellent

    Whether you are building an elite custom drivetrain or a championship manipulator, you need your components to stay where they're supposed to. These lightweight spacers come in 3/8", 1/2", and 5 mm hex bores to accommodate the most common shaft types They can also be used on round shafts and bolts (5mm is great for #10 hardware!). If you need to space a lot grab some 1" spacers. If you need ultimate precision pick up some 0.063" spacers. Not sure which spacers you need? Keep a handful of all six sizes in your shop and never go hungry for spacers again! 

    Specifications

    • Inside Diameter: 0.375 in. Hex, 0.50 in. Hex, 5 mm Hex
    • Length: 0.063 in., 0.125 in., 0.188 in., 0.250 in., 0.375 in., 0.50 in., 1.00 in.
    • Material: Polycarbonate
    • Outside Diameter: 0.787 in. Round
    • Weight: Up to 0.014 lbs

    Documents

    Layout Print(s)

    am-3947 375IN Hex Molded Spacers Layout REV4.PDF

    am-3948 500IN Hex Molded Spacers Layout REV4.PDF

    am-4535 5mm Hex Molded Spacers Layout.PDF

    Les clients ayant acheté cet article ont également acheté

    10-32 x 0.75 in. Socket Head Cap Screw - Min 25

    #am-1047
    $0,29
    (En stock)

    Specifications:

     

    • Material: Steel
    • Coating: Zinc Plated
    • Thread: 10-32
    • Length: 3/4"
    • Head: Socket Head Cap Screw

    10-32 Nylock Nut

    #am-1042
    $0,08
    (En stock)

    This item can only be purchased in multiples of 25

     

    Specifications: 

    • Material: Steel
    • Coating: Zinc Plated
    • Thread: #10-32
    • Thickness: 0.249"
    • Thread: Fine
    • Thread Size: 32
    • Type: Nylon Insert Lock Nut
    • Wrench Size: 3/8"

    #10 x 0.75 in. Fender Washer

    #am-1523
    $0,33
    ( 75 En stock)

    This item can only be purchased in multiples of 25

     

    Washers are typically used distribute a fastener load over a wider area. This washer specifically when used with a #10-32 is great for retaining a hex shaft in a hex bearing when the end of the shaft is tapped. This washer has an 0.219 inch inside diameter, 0.75 inch outside diameter, and 0.062 inch thickness.

     

    Specifications

     

    • Bolt Size: #10
    • Finish: Zinc
    • Inside Diameter: 0.219 in.
    • Material: Steel
    • Outside Diameter: 0.750 in.
    • Style: Fender Washer
    • Thickness: 0.062 in.
    • Weight: 0.006 lbs.

    #10-32 x 1.5" SHCS - Min 25

    #am-1014
    $0,38
    (En stock)

    Statistics:

    • Material: Steel
    • Coating: Zinc plated
    • Thread: #10-32
    • Length: 1-1/2 inch
    • Head: Socket Head Cap Screw

    Spacer, 1/16" thick, 1/2" Hex Bore [Qty-10]

    #am-1364
    $9,22
    (En stock)

    Specifications:

    • Quantity: 10
    • Material: Acetal
    • Inside Diameter: 0.510" Hex
    • Outside Diameter: 0.768"
    • Thickness: 0.0625"