F6's unique split, semi-rigid braided construction makes it the ideal solution for situations where ease of installation is of primary importance. The lateral split allows the tube to open up to accommodate a wide variety of bundling requirements, and the semi-rigid braid configuration simply closes around the entire installation without the need for any additional fasteners (velcro, tape, etc.) The 10 mil PET braid is lightweight, quiet and flexible. The 25% edge overlap (at nominal diameter) allows coverage around inline plugs, connectors and splices. F6 will bend to a tight radius without distorting or splitting open and, unlike full rigid tubing, will not impair or affect the flexibility of harnesses.

This Hub allows user that have existing Studica OMNI wheels (Part# 76260) or Mecanum Wheels (Part# 76243) to use REV Robotics 5mm Hex shafts and Hex Motors.

Sometimes you have the need for increased RPM. This 1:1 motor kit can be used with the Studica Maverick or any FTC legal motor such as the Neverest Classic (6600 RPM) or the REV HD Hex motor (6000RPM). The kit includes a faceplate which supports the Studica Robotics building platform. The shaft is press-fit onto the motor's shaft. It is recommended that the shaft be supported by a bearing (we recommend the 76302 for the Studica building system).

Whether you are constructing an intake, designing a shooter, or creating some other high-speed design, this 1:1 option allow you to get the full motor RPM output.

Specifications:

• Material - Anodized 6061-T6 Aluminum
• Step File

Sometimes you have the need for increased RPM. This 1:1 motor kit can be used with the Studica Maverick or any FTC legal motor such as the Neverest Classic (6600 RPM) or the REV HD Hex motor (6000RPM). The kit includes a faceplate which supports the Studica Robotics building platform. The shaft is press-fit onto the motor's shaft. It is recommended that the shaft be supported by a bearing (we recommend the 76302 for the Studica building system).

Whether you are constructing an intake, designing a shooter, or creating some other high-speed design, this 1:1 option allow you to get the full motor RPM output.

Specifications:

• Material - Anodized 6061-T6 Aluminum
• Step File

Specifications:

• Size: 1/10 standard car
• Material: Aluminum alloy
• Total length: 63mm
• Ball head to ball head: 55mm
• Diameter: 17mm 
• Ball head hole diameter: 3mm  
• Step File - Shock in compressed mode
• Step File - Shock in extended mode

Specifications:

• Size: 1/10 standard car
• Material: Aluminum alloy
• Total length: 108mm
• Ball head to ball head: 100mm
• Diameter: 17mm 
• Ball head hole diameter: 3mm 
• Step File - Shock in compressed mode
• Step File - Shock in extended mode

Used to replace or supplement connector on NI myDAQ Kit

The VMX Wallwart Barrel Plug Adapter cable connects a VMX power connector to an external 12VDC Wallwart power supply.

Detailed Specifications:

• Cable Length: 25 cm
• Wire Gauge: 20 AWG
• VMX-side Connector: JST-VH Wire Colors: Red (power), Black (ground)
• Wallwart-side Barrel Plug Connector:  2.1mm inner diameter, 5.5" outer diameter, center-positive

The VMX Battery Adapter cable connects a VMX-pi power connectcor to an external battery supply.

Detailed Specifications:

• Cable Length: 25 cm
• Wire Gauge: 20 AWG
• Connector: JST-VH Wire Colors: Red (power), Black (ground)
• Wire Free-end:  stripped and tinned

The JST-GH to JST-GH Cable connects external sensors, breakout boards or other devices.

Detailed Specifications:

• Cable Length: 25 cm
• Connectors: 4-pin JST-GH (2)
• Wire Colors: Black, Red, Blue, Green

The 5mm Round Groove Belt is 3M long and has a 10% stretch. It is also referred to as a U Groove belt. 

• Material - Polyurethane
• Diameter - 5mm
• Length - 3m
• Color - Yellow
• Stretch factor - 10%
• Surface - smooth
• Solid core
• Open end

The pulleys are .40” inside the flanges to allow for belts up to 3/8” in width. Two set screws using 1.5mm hex key.

3/8” wide, 1/5 pitch XL series belti. Constructed of Neoprene with Fiberglass cords for superior strength and wear resistance. Compatible XL series pinion pulley.

Includes two 5mm Bore, 10 Tooth Aluminum Pulleys and one 1M XL Timing belt