Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    myDAQ with NI LabVIEW and Multisim - For Students Only

    National Instrument's NI myDAQ - Student with NI LabVIEW, and Multisim, is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The NI myDAQ is a high-quality instrumentation device that gives students the power to prototype systems and test circuits outside of the classroom while improving comprehension with continuous reinforcement.

    Schools may purchase the myDAQ for secondary schools from here

    # Pièce: 781327-01
    $359.00
    Disponibilité: En stock

    View the NI myDAQ User guide and Specifications [Click Here]

    What's included:

    • NI myDAQ device
    • Powered by LabVIEW
    • Integrated Installation DVD
      • NI ELVISmx & NI DAQmx
      •  LabVIEW
      • Multisim
    • USB Cable
    • DMM Probes
    • Audio cable (3.5mm)
    • Screw Terminal connector and NI screwdriver
    • Getting Started Card
    • TI Design Competition & Samples Program Card
    • Reusable Storage Tray



    The myDAQ is a single device the has eight commonly used plug-and-play computer-based lab instruments. With NI myDAQ, the computer becomes an engineering instrument.

    Designed by National Instruments with high-quality Texas Instruments Analog Integrated Circuits (ICs), the hardware system diagram and list of Texas Instruments IC's in the NI myDAQ user guide depicts how TI data converters, amplifiers, and interface and power management circuits were used in the design of NI myDAQ.

    Extend the device's capabilities with LabVIEW and Multisim. Verify homework solutions with real signals using Multisim for circuit simulation and LabVIEW for automating measurements and performing signal processing.

    Technical Support

    Do more with NI myDAQ. Learn how to use NI myDAQ with three different software platforms, troubleshoot problems with your NI myDAQ, and ask your own questions on the discussion forums.

     

     
    Software is Windows only.

     

    Two Differential Analog Input and Analog Output Channels (200 ks/s, 16 bit, +/- 10 Volts)
    Access matched analog input and output channels in a +/- 10 volt range through the screw terminal connectors or +/- 2 volt range through the 3.5mm audio jacks.
     

    +5 , +15, and -15 Volt Power Supply Outputs (up to 500m Watts of Power)
    USB powered for maximum mobility, myDAQ supplies enough power for simple circuits and sensors.
     

    Eight Digital Input and Digital Output Lines (3.3 Volt TTL-Compatible)
    Use software-timed digital lines for interfacing both Low Voltage TTL (LVTTL) and 5 volt TTL digital circuits. Each line is individually selectable for input or output.
     

    60 Volt Digital Multimeter (DMM) for Measuring Voltage, Current, and Resistance
    The isolated DMM includes the capability to measure both AC and DC voltage and current as well as resistance, diode voltage, and continuity.
     

    Reusable Storage Box with Storage Tray, DMM Probes, and Audio Cable
    The box and storage tray provide convenient storage for your NI myDAQ and included USB cable, DMM probes, audio cable, as well as your own components and accessories.

    Écrivez votre propre commentaire
    • Le produit peut être examinée que après l'achat
    • Seul les utilisateurs enregistrés peuvent écrire une critique
    • Mal
    • Excellent

    View the NI myDAQ User guide and Specifications [Click Here]

    What's included:

    • NI myDAQ device
    • Powered by LabVIEW
    • Integrated Installation DVD
      • NI ELVISmx & NI DAQmx
      •  LabVIEW
      • Multisim
    • USB Cable
    • DMM Probes
    • Audio cable (3.5mm)
    • Screw Terminal connector and NI screwdriver
    • Getting Started Card
    • TI Design Competition & Samples Program Card
    • Reusable Storage Tray



    The myDAQ is a single device the has eight commonly used plug-and-play computer-based lab instruments. With NI myDAQ, the computer becomes an engineering instrument.

    Designed by National Instruments with high-quality Texas Instruments Analog Integrated Circuits (ICs), the hardware system diagram and list of Texas Instruments IC's in the NI myDAQ user guide depicts how TI data converters, amplifiers, and interface and power management circuits were used in the design of NI myDAQ.

    Extend the device's capabilities with LabVIEW and Multisim. Verify homework solutions with real signals using Multisim for circuit simulation and LabVIEW for automating measurements and performing signal processing.

    Technical Support

    Do more with NI myDAQ. Learn how to use NI myDAQ with three different software platforms, troubleshoot problems with your NI myDAQ, and ask your own questions on the discussion forums.

     

     
    Software is Windows only.

     

    Two Differential Analog Input and Analog Output Channels (200 ks/s, 16 bit, +/- 10 Volts)
    Access matched analog input and output channels in a +/- 10 volt range through the screw terminal connectors or +/- 2 volt range through the 3.5mm audio jacks.
     

    +5 , +15, and -15 Volt Power Supply Outputs (up to 500m Watts of Power)
    USB powered for maximum mobility, myDAQ supplies enough power for simple circuits and sensors.
     

    Eight Digital Input and Digital Output Lines (3.3 Volt TTL-Compatible)
    Use software-timed digital lines for interfacing both Low Voltage TTL (LVTTL) and 5 volt TTL digital circuits. Each line is individually selectable for input or output.
     

    60 Volt Digital Multimeter (DMM) for Measuring Voltage, Current, and Resistance
    The isolated DMM includes the capability to measure both AC and DC voltage and current as well as resistance, diode voltage, and continuity.
     

    Reusable Storage Box with Storage Tray, DMM Probes, and Audio Cable
    The box and storage tray provide convenient storage for your NI myDAQ and included USB cable, DMM probes, audio cable, as well as your own components and accessories.

    Les clients ayant acheté cet article ont également acheté

    485 Servo Pack

    #39197
    $51.33

    485 Servo Pack  is one of the best choices for rugged robotic applications. This servo’s great performance and durability are a combination of karbonite gears, high-performance circuitry, and a ball bearing-supported output shaft. Karbonite gearing is nearly four times stronger than nylon gears and provides virtually wear-free performance. Standard rotational range is 90 degrees, but it can be operated to 180 degrees with controllers capable of generating a pulse range from 600 usec to 2400 usec. Produces nearly 84 oz-in of torque power.

    Tetrix Max Servo Extension

    #39081
    $7.25

    Tetrix Max Servo Extension gives your servo a little more room to roam with this extension.

    Motor Driver and Control System Prototype Board (mySTEM 2)

    #72050
    $179.19
    (0 En stock)

    The  mySTEM 2™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices. .

    Allow you to immediately do some experiments. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Do Engineering Components Kit or visit the Spare Parts Store to create your own project.

    Includes:

    • S-Motor
    • Mini Switch
    • resisters
    • wires
    • flat plugs

    Note:  mySTEM 2 Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

    VMX FRC Training Bot

    #74000
    Demander un devis

    The Studica VMX FRC-compatible Training Bot (FRC Trainer) is a smaller, sturdy, lightweight, and less expensive robot than your typical FRC robot. If you have a large FRC team, often only a handful of students get to learn how to create and program your team’s costly competition robot.  The FRC Trainer solves this problem and is ideal for groups of two to three to participate in hands-on learning in a classroom environment.  Schools can equip their labs with multiple FRC Trainers, benefiting from the great value and compact size. Students can even take it home with them! 

    This affordable solution is intended for:

    • FRC teams that want to learn and train on a smaller and more affordable robot,
    • Schools looking for a way to teach FRC robotics in the classroom.
    • Schools that want to teach coding in the classroom through robotics.

    The FRC-compatible Trainer is an intelligent and autonomous robot that uses the VMX Advanced Robotics Controller which can be programmed in C++ and Java.  VMX’s multitude of modern digital communications interfaces and Linux-based operating system allow users to directly access most modern devices (e.g., Intel RealSense tracking and depth cameras and LIDAR).

     

    Download BOM here

     

    Basic Parts Kit for NI myDAQ

    #CK-1000.
    $122.94
    This Basic Parts Kit for the NI myDAQ provides you with 100's of parts to aid you in your prototype needs. Perform experiments first hand and develop a greater understanding of key concepts.

    TETRIX MAX Gripper Kit

    #44609
    $24.93
    (9 En stock)

    Add form and function to your TETRIX MAX robot with theTetrix Max; Gripper Kit. The integrated MAX hole pattern allows for a variety of mounting options, and the wide range will serve you well for picking up large items. The curved jaws and flat surfaces provide a more versatile gripping surface that can easily accommodate both round objects and flat objects. Removable gripper extension rails increase strength and versatility.