Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Outils

    Outils
    Voir comme Grille Lister
    Trier par
    Affichage par page

    12 AWG Gray Ferrule Crimps

    #am-3738_12
    $0.13

    errules are crimped on the metal contact rather than through the insulation like standard connectors. This means there is more contact between the wire strands and the contact point. This Ferrule can be crimped using the am-3739 crimp tool.

     

    This item can only be purchased in multiples of 25

    iCrimp Cable Lug Crimping Tool

    #HX-50BI
    $34.00
    (4 En stock)

    iCrimp Cable Lug Crimping Tool for Heavy Duty Wire Lugs,Battery Terminal,Copper Lugs AWG 8-1/0

     

    •  6 dies in AWG: 8,6,4,2,1,1/0
    •  Hexagonal rotating dies are processed with Wire EDM Cutting, more accurate than normal casting dies.
    •  Comfortable grip with antislip surface saves strength and improves user’s experience.
    •  Made of high quality carbon steel which can offer long service life.
    • Compatiable with copper&aluminum cable lug,non-welding and standard electrical connection.

     

    ICrimp Insulated Terminal Ratchet Wire Crimping Tool Kit

    #IWS-03C+KIT285
    $34.71
    (10 En stock)
    iCrimp Insulated Terminal Crimping Tools Ratchet Wire Crimper with 285pcs Insulated Butt, Spades, Rings Connectors from AWG22-10

    iCrimp Open Barrel Crimper

    #IWS-2412M
    $22.99
    (10 En stock)
    iCrimp Open Barrel Crimping Tools Works on AWG24-12 JAM, Molex, Tyco, JST Terminals and Connectors

     

    Purpose: IWS-2412M open barrel crimper tool is designed to crimp non-insulated open barrel, OEM-style terminals. Perfect for servo lead connectors and some other RC crimp connectors.

     

    iCrimp Mini Micro Open Barrel Crimper

    #IWS-2820M
    $23.99
    (10 En stock)
    iCrimp Mini Micro Open Barrel Crimping Tools Works on AWG28-20 JAM, Molex, Tyco, JST Terminals and Connectors

     

    IWS-2820M open barrel crimper tool is designed to crimp non-insulated open barrel, OEM-style terminals. Perfect for servo lead connectors and some other RC crimp connectors.

    #35 Chain Break Replacement Bolt with Pin

    #am-1516
    $14.00
    (2 En stock)

    This bolt with pin is a replacement for the #35 chain break. This component does the work of pushing a pin out of a chain link.

     

    Specifications

     

    • Drive: 1/4 in. Hex
    • Weight: 0.033 lbs

    Polybelt Welder Hot Knife

    #am-5284
    $55.00
    (3 En stock)

    This hot knife is a convenient way to seal the end of a fraying rope or melt the ends of Polybelt to make a loop. 

    Polybelt Welder Clamp Tool

    #am-5285
    $67.50
    (2 En stock)

    This assembly is used to easily make custom lengths of Polybelt loops. A set of thumb screws are included to make clamping belt ends simple. The over-center linkage makes it easy to bring the melted belt ends together and hold in place while the belt cools. This makes installing a custom-length polybelt loop on your mechanism easier than ever. This tool can accept polyurethane belts up to 2 inches wide. 

     

    Usage:

    1.) Place cut belt ends under the clamping plates with about 1/16 inch hanging toward the inside. If using 1 or 2 inch wide belt, align the sides to the alignment notches.

     

    2.) Tighten the thumb screws on both sides until the belt is snug.

    3.) Using a heat source like our Belt Welding Hot Knife (am-5284) heat up the belt ends until they start to melt.

    4.) Once the ends start to melt, immediately close the clamp to press the melted ends together.

    5.) When cool, loosen the thumb screws on the slotted sides of the clamp (note indicator holes for reference) and remove clamp from belt.