This 12 tooth pinion gear is designed to fit onto an AndyMark RedLine Motor (am-3775) and other motors with a 5 mm output shaft to interface with spur gearboxes such as the DeCIMate (am-3745), EVO Slim for RedLine and EVO Shifter for RedLine. 

Specifications:

• Bore: 5mm press fit
• Weight: 0.014 Pounds
• Material: 1117 Steel
• Overall Length: 0.755 in.
• Face Width: 0.625 in.
• Tooth Count: 12
• Pitch Diameter: 0.375 in.
• Pressure Angle: 20
• Diametral Pitch: 32

Specifications:

• Tooth Count: 14
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 0.7
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex
• Weight: 0.029 Lbs

This gear is used as the input pinion gear for the EVO Shifter. This gear is a tight press fit onto a CIM gear, and requires at minimum a 3-ton arbor press to install. If a CIM motor with this gear pre-installed interests you, check out am-0255_15T. 

Specifications:

• Tooth Count: 15
• Diametral Pitch: 32
• Pressure Angle: 20
• Pitch Diameter: 0.469"
• Face Width: 0.531"
• Thickness: 0.75"
• Material: 1117 Steel
• Bore: 0.312" Round (7.92mm) This is a press fit onto the CIM Motor (am-0255)
• Weight: 0.019 Lbs

This gear can be used on the any of the PG Series Gearmotors, fitting on the 10mm output shaft. 

Specifications:

• Number of Teeth: 16
• Diametral Pitch: 20
• Pitch Diameter: 0.8"
• Pressure Angle: 14.5 Degrees
• Pitch Diameter: 0.8"
• Face Width: 0.55"
• Overall Width: 0.58"
• Bore: 10mm (0.395") diameter hole w/ 4mm (0.158") keyway
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.08 Pounds

This pinion gear attaches to an CIM style motor or gearbox so it can be used with a CIM Sport Gearbox.

Specifications:

• Tooth Count: 16
• Module: 0.7
• Pressure Angle: 20
• Pitch Diameter: 0.44 in.
• Overall Length: 0.35 in.
• Material: Steel
• Bore: 0.312" Round (7.92mm) This is a press fit onto the CIM Motor (am-0255)
• Weight: 0.008 Pounds

Specifications: 

• Material: 4140 Steel
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Number of teeth: 17
• Pitch diameter: 0.85 inch
• Bore: 0.313 inch (8mm), with 2mm keyway
• Gear face width: 0.375 inch
• Weight: 0.04 pound

Specifications:

• Tooth Count: 18
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 0.9"
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex

Miter gears are a special class of bevel gears where the shafts intersect at 90° and the gear ratio is 1:1. This miter gear has a .500" hex bore, making it perfect for interfacing with many popular products in the competition robotics marketplace.

Specifications:

• Material: 1045 Steel
• Module: 1.25
• Tooth Count: 20
• Pressure Angle: 20
• Pitch Diameter: 0.980 in
• Mounting Distance: 0.910 in
• Hub Depth: 0.350 in
• Hub Diameter: 0.870 in
• Bore: 0.50 in Hex
• Weight: 0.056 Pounds

Specifications:

• Tooth Count: 20
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1 in.
• Face Width: 0.375 in.
• Material: 4140 Steel
• Bore: 0.375 in.
• Weight: 0.07 Pounds

This gear is a press fit gear specifically designed for the 2 Stage EVO Shifter Output shafts, as part of the encoder setup.

Specifications:

• Tooth Count: 20
• Diametral Pitch: 32
• Pressure Angle: 20
• Pitch Diameter: 0.625"
• Face Width: 0.62"
• Material: 1117 Steel
• Bore: 0.372" Round
• Weight: 0.03 Lbs

Miter gears are a special class of bevel gears where the shafts intersect at 90° and the gear ratio is 1:1. This miter gear has a 8mm bore with a 2mm keyway, fitting perfectly on a CIM motor shaft. 

Specifications:

• Material: 1045 Steel
• Module: 1.25
• Tooth Count: 20
• Pressure Angle: 20
• Pitch Diameter: 0.980 in
• Mounting Distance: 0.910 in
• Hub Depth: 0.350 in
• Hub Diameter: 0.870 in
• Bore: 8 mm with 2 mm keyway
• Weight: 0.078 Pounds

Specifications:

• Tooth Count: 24
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.2"
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex
• Weight: 0.1 Lbs

Specifications:

• Tooth Count: 25
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.25"
• Face Width: 0.5"
• Material: 4140 Steel
• Bore: 0.5" Hex

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear

Specifications:

• Tooth Count: 32
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.6 in.
• Face Width: 0.375 in.
• Material: 4140 Steel
• Bore: 0.50 in. Hex
• Weight: 0.11 Pounds