Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Passive Power Over Ethernet Injector

    Have you lost OpenMesh Radio power during a match because the barrel came unplugged? You can keep that from happening ever again by using this Power Over Ethernet (POE) injector. This injector inserts POE power to a CAT5 Ethernet data cable on the unused Ethernet pins 4,5(+) and 7,8(-) allowing you to stop the worry about the barrel connector failures.
     

    The barrel connector will still need to be used but it can move to a more secure location that can be wrapped with electrical tape to keep it in place better than attempting to tape it to the back of the OpenMesh Radio.
     

    Plug in the RJ-45 of this unit to your roboRIO, plug the same 12V barrel connector from your Voltage Regulator Module (VRM) into the power port, securely tape it in place with electrical tape (better than awkwardly to the back to the OpenMesh Radio), and run an Ethernet cable from the female port to the Ethernet port closes to the power input on your OpenMesh Radio.

     

    Specifications

    • Length: 9.5 in.

     

    Documents

    Guide(s)

    am-3766 Using the POE Injector.pdf

    # Pièce: am-3766
    $16.00
    Disponibilité: En stock
    Écrivez votre propre commentaire
    • Le produit peut être examinée que après l'achat
    • Seul les utilisateurs enregistrés peuvent écrire une critique
    • Mal
    • Excellent
    Les clients ayant acheté cet article ont également acheté

    6 Gauge Compression Lug Connector 1/4 Stud Hole BURNDY #: YAZV6CTC14FX

    #am-0805
    $5.50
    (256 En stock)

    This is a heavy-duty compression lug from BURNDY for 06 AWG wire. This compression log can be easily crimped with the Cable Lug Crimping Tool.

     

    Specifications

    • Gauge: 06 AWG
    • Hole Size For Stud: 0.25 in.
    • Material: Copper
    • Overall Length: 2.03 in.
    • Tongue Width: 0.48 in.
    • Weight: 0.01 lbs
    • Wire Strip Length: 1.18 in.

    #35 Connecting Link for Roller Chain

    #am-0368
    $1.75
    (En stock)

    #35 Connecting Link (Master Link) 

    Specifications:

    • Material: Steel
    • Style: Roller Chain - Spring Clip
    • Type: Connecting Link
    • Size: #35
    • Pitch: 0.375 inch
    • Weight: 0.01 lbs

    1/2 in. Hex Collar Clamps, Silver Thin (0.25in) - 1 part

    #am-1635
    $6.95
    (39 En stock)

    These custom designed collar clamps have been designed specifically with FIRST Robotics Competition teams in mind. The one-piece collar clamp is a nice fractional 1/2 in. width to make shaft stackups easy. The clamping force is provided by a 10-32 socket head screw, which is bigger than most used in the competition marketplace.  This provides a high-strength clamping solution that shouldn't strip out when you need it most. You can even replace the 10-32 screw if it becomes lost with the screws historically used in the AM14U family of chassis. These thoughtfully designed collar clamps also have small bosses on each side. This allows these collar clamps to be installed directly adjacent to an FR8ZZ Round or FR8ZZ Hex bearing without rubbing on the outer races for smooth operation.

    Bearing, 1/2 inch Hex Bore, Flanged, (FR8ZZ-HexHD)

    #am-2986
    $8.00
    (87 En stock)

    This is a Heavy Duty Hex Bearing which outperforms our previous 1/2" Hex Bearings as it has a Heavy Duty Inner Race. This FR8ZZ-HexHD bearing, 1/2" hex bore, flanged, heavy duty inner race, shielded ball bearing, has an inner race that is thicker and stronger than our recent offering of a similar bearing (am-0279). This bearing has more material between the corners of the hex bore and the edge of the race making it stronger and much less likely to crack under high load.

    This bearing is guaranteed to have a stronger, thicker race. 100% of these bearings have been quality checked for a smooth fit over 1/2" hex stock here at AndyMark. Many of our long-time customers will recognize this bearing, as it is the same version we sold back in 2008-2011, and we did not have any failures. Now, it is renamed and quality checked for your high load needs - including drive chassis with cantilevered wheels.


    Specifications:

    • Inside diameter: 0.500-0.502 inch hex bore
    • Outside diameter: 1.125 inch
    • Flange thickness: 0.062 inch
    • Overall thickness: 0.312 inch
    • Weight: 0.05 pound

    24T HTD Pulley, 1/2" Hex Bore

    #am-3403
    $13.85
    (En stock)

    Specifications:

    • Flange diameter: 1.654"
    • Outside Diameter: 1.459"
    • Pitch Diameter: 1.504"
    • Width: 0.276"
    • Bore: 0.50" Hex
    • Material: Black Polycarbonate
    • Fits belt types: 5mm pitch HTD timing belt, 9mm wide
    • Weight: 0.0025 Pounds

    40 Amp Snap Action Breaker

    #am-0288
    $11.00
    (En stock)

    Snap action breakers are used commonly in mobile robot applications such as FIRST Robotics Competition power distribution boards. We offer several amperage versions. 

     

    Specifications

    • Manufacturer: Snap Action
    • Style: MINI, Auto-resetting
    • Voltage: Up to 50V DC