Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Pignons et Chaînes

    Tubes et bagues
    
    Voir comme Grille Lister
    Trier par
    Affichage par page

    6 mm x 8 mm Bushing, Nylon

    #am-1289
    $0,47 $0,53
    (En stock)

    This bushing fits into any 8mm hole such as those seen on tubing in the S3 Ecosystem. The bushing supports a 6mm shaft allowing you to use our precision 6mm D Shafts with the S3 Ecosystem and other systems. 

    Specifications:

    • Inner Diameter: 6mm (0.24 in.)
    • Outer Diammeter: 8mm (0.31 in.)
    • Overall Length: 6mm (0.24 in.)

    Arm Joint for PVC pipe

    #am-2699
    $53,81 $60,77
    (En stock)


    Looking for a quick way to make an arm joint? This kit quickly mounts to a 2 inch PVC pipe then either a hub or bearings to mount for a joint.


    Hardware Included:

    • Two - PVC Joint Plates
    • Two - PVC Joint Spacers
    • Four - Individual 1/4-20 x 3" Screws (buy 10 am-1209)
    • Four - Individual 1/4-20 Nylock Nuts (am-1015)
    • Four - Individual 10-32 x 3" Screws (buy 25 am-1201)
    • Four - Individual 10-32 Nylock Nuts (buy 50 am-1212)


    Usage:

    • - With a Hub: Mount any one of our hubs and you can drive this joint for an arm with a direct output from our gearboxes with your specified shaft.
    • - With a Bearing: Place a bearing in the plates and you can use a dead axle and a driven sprocket to drive this joint.

    Specifications

    • Height: 5 in.
    • Length: 3.5 in.
    • Weight: 1.10 lbs
    • Width: 2.75 in.

    Arm Joint Plate (am-2692)

    #am-2692
    $15,38 $17,36
    (En stock)


    The Plate used in the PVC Arm Joint

    Specifications

    • Height: 3.505"
    • Length: 5"
    • Material: 6061 Aluminum
    • Thickness: 0.188"
    • Weight: 0.22 lbs

    Black SBR Roller

    #am-0049
    $1,16 $1,31
    (En stock)

    These black rubber rollers are used in AndyMark omni wheels . Each roller rides on 2 brass eyelets, which spin on one steel 1/8" dowel pin.

    Specifications:

    • Color: Black,non-marking
    • Diameter: 3/4" (at center)
    • Durometer: 80A
    • Length: 3/4"
    • Material: SBR rubber
    • Weight: 0.018 lbs

    0.82" x 3/8" Spacer

    #am-2243
    $2,31 $2,61
    (En stock)

    This is a 0.82 inch long brass spacer which fits over a 3/8" shaft.

    Specifications:

    • Length: 0.82"
    • Inside diameter: 0.379"
    • Outside diameter: 0.437"
    • Material: Brass
    • Weight: 0.01 Lb

    1.8" x 3/8" Spacer

    #am-2242
    $4,61 $5,21
    (En stock)

    This is a 1.8 inch long brass spacer which fits over a 3/8" shaft.

    Specifications:

    • Length: 1.80"
    • Inside diameter: 0.379"
    • Outside diameter: 0.437"
    • Material: Brass
    • Weight: 0.022 Lb

    1/2" id, 1/2" Long Bushing

    #am-0253
    $3,85 $4,35
    (En stock)

    Steel sleeve bushing with self-lubricating bearing surface 

    Specifications:

    • Structure material: steel
    • Lubrication material: TPFE, located on the inside diameter
    • Bore: 0.500 inch
    • Outside diameter: 0.598 inch
    • Overall length: 0.500 inch
    • Weight: 0.012 pounds

    Omni-Roller Sleeve

    #am-0050
    $0,38 $0,43
    (En stock)

    Eyelet used in AndyMark omni wheels

    2 eyelets are used within each roller. These eyelets spin on 1/8" dowels to provide the spinning action of each roller on an AndyMark omni wheel. 

    Specifications:

    • Material: Brass
    • Overall length: 0.33"
    • Inside diameter: 0.13"
    • Outside diameter: 0.155"
    • Flange diameter: 0.29"
    • Wall thickness: 0.012"
    • Weight: 0.0006 pounds

    RD Brass Tubing .250 x .014 x .335"

    #am-0300
    $1,54 $1,74
    (En stock)

    Brass tubing spacer used in the Shifter Assembly of the AM Shifter and Super Shifter 

    Specifications:

    • Weight: 0.001 pounds
    • Length: 0.335"
    • Outer Diameter: 0.250"
    • Inner Diameter: 0.215
    • Material: Brass

    RD Brass Tubing 1/2 x .442 x 0.565/0.585

    #am-0712
    $2,31 $2,61
    (En stock)

    Brass Tubing Spacer used in Super Shifter gearbox. 

    Specifications:

    • Material: Brass
    • Length: 0.58"
    • Inner Diameter: 0.442"
    • Outer Diameter: 0.50"
    • Weight: 0.008 Lb

    RD Brass Tubing 1/2 x .442 x 1.152/1.172

    #am-0333
    $3,08 $3,47
    (En stock)

    Brass Tubing Spacer used in the AM Shifter. 

    Specifications:

    • Weight: 0.015 pounds
    • Length: 1.152" - 1.172"
    • Outside Diameter: 0.5"
    • Inside Diameter: 0.442"
    • Material: Brass

    Rubber "Surgical" Tubing Black 10 Feet

    #am-3581
    $42,00 $47,76
    (En stock)

    Surgical tubing is a great all purpose robot product! It can be used in applications as varied as wrapping it around a spinning pipe to help grip objects, to counterbalancing an arm with it's spring force, or to coupling an encoder to a misaligned shaft. The possibilities are endless!

    Specifications:

    • Inside Diameter: 0.125 in.
    • Material: Natural Latex Rubber
    • Outside Diameter: 0.375 in
    • Wall Thickness: 0.125 in.

    5/8 in. ID, 7/8 in. OD Black Surgical Tubing - 10 Feet

    #am-4656-10
    $44,00

    This Surgical Tubing is most often used in robotics to create custom rollers, such as the AndyMark Tube Roller. This stretchy rubber latex tubing has so many more uses though! This black wonder material is a must-have for griping game elements when paired with our Aluminum Hex Spacer Stock.

    Choose between 3 feet and 10 feet lengths.

    To install this grippy tubing on Hex Spacer Extrusion use hand sanitizer or soapy water to lubricate the aluminum, then slide the tubing over and wait for the lubricant to evaporate. You can then power the assembly with a 1/2" hex shaft to intake game pieces or move them around inside your robot. 

     

    Specifications

    • Inside Diameter: 0.625 in.
    • Wall Thickness: 0.125 in.