Three (3) straight 1/8 NPT fittings (or right angle 1/8 NPT fittings) are NOT INCLUDED with this part, but are needed to connect tubing to this valve.

Specifications:

• Type: In-line, individual
• Size: 170mm x 67mm x 22mm
• Valve function: 5 Port-2 Position
• Port size: 1/8" NPT
• pilot air supply: Internal
• Cable length:
• Voltage: 12Vdc
• Weight: 0.72 lbs
• Pressure Range: 22 - 116 psi
• Max. pressure: 215 psi
• Max Response Time: 50ms
• Flow rating: 0.78 Cv

VIAIR 90C compressor (air pump) offers a light duty solution for smaller air requirements. These compact compressors and are meant to fill no larger than a 1.0 gallon air tank. 

VIAIR part number 00090

Specifications:

• Manufacturer: VIAIR Corporation
• Weight: 2.4 pounds
• Width: 2.11 inches
• Height: 4.53 inches
• Length: 5.94 inches
• Material: Steel and aluminum
• Manufacturer: Viair Corporation
• Part Number: 00090
• Flow Rate: 0.88 cfm at 0 ps
• Ports: 1/8" NPT
• Voltage: 12 Volt DC
• Permanent Magnet Motor
• Duty Cycle: 9% @ 100 psi
• Maximum Working Pressure: 120 psi
• Maximum Amp Draw: 11 amps

Hardware: 

• Vibration Isolators (4)
• Screw (4)
• Nut (4)
• Washer (8)
• Lock Washer (4)

Fill Rate

• This pump will take approximately 13 seconds to fill one (1) plastic Clippard tank (574 ml) from 0 to 120 psi.

Products to be used on:

• Mobile Robots
• Outdoor equipment

For VIAIR compressor warranty replacements contact Ryan Shaw.

• Phone: 949-585-0011 x110
• Email: [email protected]

This is a polypropylene plastic air tank accumulator holding 36.0 cubic inches (~590ml) up to a pressure of 125 psi and a burst rating of 500 psi.

This tank has 1/4" NPT ports (2).

Specifications:

• Weight: 0.64 pound
• Capacity: 36.0 cubic inches (590 ml)
• Ports: Two 1/4" NPT female (one on each end)
• Material: Polypropylene Plastic
• Working pressure rating: 125 psi
• Burst pressure rating: 500 psi
• Max. temperature rating: 100 F
• Length: 12.1 inches
• Diameter: 2.7 inches

This is a steel ball valve, with a large plastic handle. On mobile robots, this can act as a vent valve. It has two ports, one being a 1/4" NPT male and one being a 1/4" NPT female port

Specifications:

• Weight: 0.19 pound
• Width: 1.71 inch
• Height: 1.45 inch
• Hex Body Width: 0.82 inch
• Material: Steel, chrome plated
• Manufacturer: Midwest Control
• Part Number: CMVL-25
• Capacity: 450 psi (cold working pressure)
• Medium: compressed air
• Temperature Range: -4 to 250 degrees F
• Ports: 1/4" NPT (one male, one female)

This is a steel sheet metal bracket designed to mount the phd, Inc. OCG cylinders (am-3303, am-3304, am-3305).

Specifications:

• Manufacturer Part Number: 86993-01
• Bracket Material: steel
• Bracket Thickness: 1/8 inch
• Bracket Width: 1.75 inches
• Bracket Height: 1.375 inches
• Bracket Depth: 0.875 inches
• Weight: 0.1 pound (bracket and fasteners)

Included Hardware:

• One - Sheet metal bracket
• Four - #8-32 x 3/8" BHCS
   

This is a plastic bracket for mounting the Clippard Air Tank (am-2649).

If you plan to use this bracket to hold of these am-2649 tanks, we recommend using two brackets for each tank. 

Specifications:

• Weight: 0.066 pound
• Width: 3.14 inches
• Height: 2.65 inches
• Thickness: 0.75 inch
• Material: Plastic

For Pro Charging Systems, warranty replacements contact Richard Harmon. 

• Email: [email protected]

This is an single solenoid, air-piloted, compact valve made by CKD. It's great for efficiently providing air to a small to medium sized actuator on mobile robots.

In order to make this work, you will also need three (3) M5 fittings (NOT INCLUDED) and some tubing (also NOT INCLUDED).

Link to CKD valve catalog

CKD part number: 4GA110R-M5-4

Specifications

• Cable Length: 3ft
• Flow Rate: 0.3 Cv
• Manufacturer: CKD
• Manufacturer Part #: 4GA110-M5-4
• Maximum Pressure: 125 psi
• Port(s): M5
• Voltage: 12Vdc
• Weight: 0.1 Lbs
• Width: 12mm

This is a plastic air tank accumulator holding 574 ml, manufactured by Clippard.

This black plastic tank has been improved over the last white plastic design from Clippard. Each end now has molded in plastic push-in fittings. These eliminate the need to have metal fittings to be screwed in to the tank, and omits the uncertainty of over-tightening a fitting into the tank.

Specifications:

• Manufacturer: Clippard
• Weight: 0.64 lbs
• Capacity: 574 ml (35 cu. inch)
• Ports: Two 1/4" od tube push-in fittings
• Maximum pressure: 125 psig
• Temperature rating: 35 to 100 F
• Length: 12.25"
• Diameter: 2.5" (@ main tank), 2.75" max

A mounting bracket is available to order (am-2008), but is not included when ordering just this item.

Note: If you have received a faulty air tank (damaged push to connect fittings) please contact Scott Lamb of Clippard Technical Sales at (513)-521-4445 (ext 1213).

This is a brass plug for a 1/4" NPT port.

Specifications:

• Weight: 0.3 lbs
• Height: 0.593 in
• Material: Brass with nickel plating
• Hex width: 17 mm or 11/16 in wrench
• Ports: 1/8" NPT male
• Pressure range: 0-250 psi

This is a Nylon plug for a 1/4" NPT port.

Specifications

• Hex Width: 0.525"
• Length: 0.715"
• Material: Nylon
• Operating Pressure: 0-200 psi
• Port(s): 1/8" NPT male
• Weight: 0.01 lbs

This is a brass plug for a 1/8" NPT port.

Specifications:

• Weight: 0.018 pounds
• Hex width: 0.44"
• Height: 0.52"
• Material: Brass
• Ports: 1/8" male
• Pressure range: 0-250 psi

This is a Nylon plug for a 1/8" NPT port.

Specifications

• Hex Width: 0.435"
• Length: 0.575"
• Material: Nylon
• Operating Pressure: 0-200 psi
• Port(s): 1/8" male
• Weight: 0.01 lbs

This is a 20 meter length of black, polyurethane pneumatic tubing.

Specifications: 

• Outside Diameter: 0.25 inch
• Inside Diameter: 0.15-0.16 inch
• Length: 20 meters (66ft)
• Material: Polyurethane
• Color: Black
• Pressure Rating: 125 psi at 75 degrees Fahrenheit (see here for manufacturer's support of this rating)
• Weight: 1.1 pounds for 20 meters

This is a fitting intended on remotely-mounting a pressure gauge. This fitting can be mounted to a panel, through a 9/16" hole, and it has a 1/8" NPT female port.

Specifications:

• Weight: 0.08 pound
• Width: 0.69 inch
• Height: 1.23 inch
• Material: Steel with plastic
• Medium: air pressure
• Ports: 1/8" NPT female
• Pressure range: 0-150 psi

This kit is all the fittings you need to use 4 CKD valves next to each other on the Four Slot CKD Pneumatic Manifold (am-3982). If you decided to ever remove any of the valves one CKD Manifold Blank Cover (am-4003) would be needed for each unused port.

Included Parts:

• 8 - M5 Pisco Fitting for 1/4 in. press-in tube (am-2384)
• 4 - M5 Pneumatic Fitting Extension (am-4004)

This is a brass adapter fitting with a male 1/8" NPT thread and a female 1/4" NPT port.

This fitting helps out an application when a device with a 1/4" NPT male thread needs to fit into a 1/8" NPT female port.

Specifications:

• Weight: 0.05 lbs
• Length: 0.91 inch
• Hex width: 0.67 inch, turned with a 11/16 wrench
• Material: Brass with nickel plating
• Ports: 1/8" NPT male, 1/4" NPT female
• Pressure rating: 230 psi