This is a straight line Union Hex Nipple with 1/8 NPT Thread on both sides.

Specifications:

• Weight: 0.01 lbs
• Width: 0.39 in
• Length: 0.825 in
• Material: Brass with nickel plating
• Hex width: 0.5 in
• Ports: Two Male 1/8" NPT Thread
• Pressure range: 0-250 psi

This is a Nickel plated Brass cross union with three (3) Female connections with 1/8 NPT thread and one (1) male connection at 1/8 NPT.

This part can replace heavier brass manifold pieces and makes your pneumatic system lighter.

Specifications:

• Weight: 0.08 lbs
• Width: 1.65 in
• Height: 0.51 in
• Depth: 1.58 in
• Material: Brass with nickel plating
• Ports: 3 Female 1/8 NPT, 1 male 1/8 NPT
• Pressure rating: 230 psi

This is a straight line Union Hex Nipple with 1/4" NPT Thread on both sides.

Specifications:

• Weight: 0.01 lbs
• Length: 1"
• Material: Nylon
• Hex width: 0.425"
• Ports: Two Male 1/4" NPT Thread
• Pressure range: 0-200

This is a straight line Union Hex Nipple with 1/8 NPT Thread on both sides.

Specifications:

• Weight: 0.01 lbs
• Length: 1.25"
• Material: Nylon
• Hex width: 0.565"
• Ports: Two Male 1/8" NPT Thread
• Pressure range: 0-200 psi

This is an elbow fitting with 1/4" NPT Thread and a 1/4" press-in-connector.

Specifications:

• Weight: 0.3 lbs
• Width: 1.37 in
• Depth: 1.09 in
• Height: 0.63 in
• Material: Brass with nickel plating with plastic body
• Hex width: 0.5 in
• Ports: Two Male 1/4" NPT Thread
• Pressure range: 0-150 psi

This is a push-to-connect "Y" fitting.

Specifications:

• Weight: 0.02 lbs
• Width: 1.515 in
• Height: 0.56 in
• Depth: 1.31 in
• Material: plastic body material
• Ports: 1/4" push-to-connect fitting
• Pressure range: 0-150 psi

This is a pneumatic Y connection with two 1/4" push-to-connect fittings and one 1/8" NPT thread end.

Specifications:

• Weight: 0.03 lbs
• Width: 1.025 in
• Height: 0.525 in
• Length: 1.825 in
• Material: >Brass with nickel plating, with plastic body material
• Hex width: 0.5 in
• Ports: 1/4" push-to-connect fitting
• Pressure range: 0-150 psi

This is a Nickel plated Brass "Y" union with two (2) Female connections with 1/8 NPT thread and one (1) male connection at 1/8 NPT.

Specifications:

• Weight: 0.05 lbs
• Width: 1.54 in
• Height: 0.51 in
• Depth: 1.09 in
• Material: Brass with nickel plating
• Ports: 2 Female 1/8 NPT, 1 male 1/8 NPT
• Pressure range: 0-250 psi

This is a pneumatic in-line flow control fitting, with flow metering as the air exits (meter out) through the push-to-connect fittings.

Specifications:

• Weight: 0.06 pound
• Width: 1.8 "
• Height: 1.6"
• Depth: 0.6
• Ports: 1/4" Diameter Tube Press In
• Pressure range: 0-150 psi
• Flow Control: Meter out

Now, you can put your CKD valves on a light weight 4-bank aluminum manifold. 

This is a hex nipple brass fitting, with one end being 1/4" NPT and the other being 1/8" NPT port. The intent of this part is to connect the air compressor (pump) to the aluminum manifold within the Pneumatics Base Kit.

Specifications:

• Weight: 0.05 pound
• Length: 1.15 inch
• Hex Width: 9/16 inch
• Material: Brass
• Ports: 1/4" NPT and 1/8" NPT
• Pressure range: 0-250 psi

This is an all in one in-line pressure regulator and low pressure side gauge perfect for lightweight pneumatic systems where you need to mount a regulator somewhere downstream in the system.

This is a miniature pressure regulator with 1/4 in. push to connect fittings perfect for lightweight pneumatic systems where you need to mount a regulator downstream in your pneumatics system. Combining push to connect fittings with the miniature regulator makes installation anywhere in your robot fast and simple.  This regulator is significantly reduced in volume and weight compared to the classic regulators used in FRC. This lets you take advantage of every last cubic inch and ounce on your robot.

Specifications

• Depth: 0.98 in
• Height: 2.40 in
• Operating Pressure: 0-150 psi
• Port(s) : (2) 1/4 in. Female Press-In
• Width: 2.15 in

Be sure all your threaded pneumatic connections are sealed properly with this teflon tape. Standard grade PTFE tape used in all your robot pneumatics.

Specifications:

• Width: 1/2"
• Length: 520"
• Material: PTFE

Pneumatic fitting with M5 threads and 1/4" push-in tubing port

This fitting screws into a CKD single or double solenoid valve. 

Specifications:

• Pisco fitting, part number POC1/4-M5
• Tubing diameter: 1/4 inch
• Mounting thread: M5
• Fastening method: Internal hex (use allen wrench)
• No pipe tape or additional sealant is needed for fastening these fittings
• Pressure rating: 150 psi

This is an air pressure switch with a factory preset setting of 115-120 psi. This switch is able to send a signal to a robot controller, which can then tell a pneumatic compressor (air pump) to stop operating.

Specifications

• Circuit: SPST-NC
• Current Rating: 5 amps @ 30 VDC
• Cycle Life: 1 million
• Fixed set point: 115 psi
• Manufacturer: Nason
• Manufacturer Part #: SM-2B-115R/443
• Maximum Operating Pressure: 250 psi
• NEMA Rating: NEMA 4, 13
• Port(s): 1/8 in. NPT Male
• Screw Terminals: #8-32
• Set Point Direction: Rising

Documents

Guide(s)

am-2006 Data Sheet.pdf