This is a brass relief valve used in low-volume air tanks and pumps to retard excessive pressure buildup.

Specifications:

• Weight: 0.09 Pounds
• Maximum Operating Pressure: 250 PSI
• Outlet Pressure Adjustment: 125 PSI
• Valve Type: Pop Safety
• Test Mechanism: Ring
• Material: Nickel-Plated Brass
• Operating temperature range: -15 to 250 degrees F
• Port size: 1/8 in. NPT Male

This is a steel sheet metal bracket designed to mount the phd, Inc. OCG cylinders (am-3303, am-3304, am-3305). It acts as a pivot mount for the front part of the cylinder.

Single solenoid pneumatic valve without fittings, manufactured by Mead Fluid Dynamics, Inc.

Mead part number: M4V210-06-12VDCFL
 

Three (3) straight 1/8 NPT fittings (or right angle 1/8 NPT fittings) are NOT INCLUDED with this part, but are needed to connect tubing to this valve.

Specifications

• Flow Rating: 0.78 Cv
• Maximum Pressure: 215 psi
• Maximum Response Time: 50ms
• Operating Pressure: 22 - 116 psi
• Pilot Air Supply: Internal
• Port(s): 1/8 in. NPT
• Size: 117mm x 67mm x 22mm
• Style: In-line, individual
• Valve Function: 5 Port-2 Position
• Voltage: 12Vdc
• Weight: 0.52 lbs

This is the ultimate step in our pneumatics packages. Plenty of extras for backup parts and multiple actuation. All while creating pressurized air in a safe, manageable manner for mobile robots.

VIAIR 90C compressor (air pump) offers a light duty solution for smaller air requirements. These compact compressors and are meant to fill no larger than a 1.0 gallon air tank. 

VIAIR part number 00090

Specifications:

• Manufacturer: VIAIR Corporation
• Weight: 2.4 pounds
• Width: 2.11 inches
• Height: 4.53 inches
• Length: 5.94 inches
• Material: Steel and aluminum
• Manufacturer: Viair Corporation
• Part Number: 00090
• Flow Rate: 0.88 cfm at 0 ps
• Ports: 1/8" NPT
• Voltage: 12 Volt DC
• Permanent Magnet Motor
• Duty Cycle: 9% @ 100 psi
• Maximum Working Pressure: 120 psi
• Maximum Amp Draw: 11 amps

Hardware: 

• Vibration Isolators (4)
• Screw (4)
• Nut (4)
• Washer (8)
• Lock Washer (4)

Fill Rate

• This pump will take approximately 13 seconds to fill one (1) plastic Clippard tank (574 ml) from 0 to 120 psi.

Products to be used on:

• Mobile Robots
• Outdoor equipment

For VIAIR compressor warranty replacements contact Ryan Shaw.

• Phone: 949-585-0011 x110
• Email: [email protected]

This is a miniature pressure gauge with two 1/4 in. push to connect fittings for in line installations. It is perfect for lightweight pneumatic systems where you need to mount a pressure gauge in line with a tubing run. This pressure gauge is significantly reduced in volume and weight compared to the classic gauges used in FRC. This lets you take advantage of every last cubic inch and ounce on your robot.

Specifications

• Depth: 0.51
• Height: 1.27
• Operating Pressure: 0-150 psi
• Port(s): (2) 1/4 in. Female Push-in
• Pressure Range: 0-116 psi
• Width: 1.58

This is a pneumatic meter-out flow control valve. The port is a 1/8" NPT male thread, and 1/4" diameter tube can be pressed in to the push-to-connect fitting.
 

Meter-out allows for the flow to be controlled in one direction, while the opposite flow is not restricted.

Specifications

• Hex Width: 7/16 in.
• Material: Rotating thermoplastic (PBT) body, nickel-plated brass threads, stainless steel tube griping claws, and pre-applied Teflon thread sealant
• Port(s): 1/8 in. NPT male with pre-applied Teflon thread sealant
• Weight: 0.01 lbs

This is a double solenoid, air-piloted, compact valve made by CKD. It's great for efficiently providing air to a small to medium sized actuator on mobile robots. This valve does not have any sort of base, as it mounts directly on the CKD manifold base (am-3982). Unlike previous versions like this valve the signal wires are NOT able to disconnected from the valve. As such we don't recommend you try to remove them.
 

Compatible Fittings not Included:

• M5 1/4 in. Tube Press-In (am-2384)
• M5 Extension Screw Adapter (am-4004)

CKD Information:

Link to CKD valve catalog

CKD part number: 4GA129R-M5-4

Specifications

• Cable Length: 11 in.
• Fitting Connections: M5 Thread
• Flow Rating: 0.3 Cv 3000/min
• Maximum Pressure: 125 psi
• Port(s): M5
• Style: In-line manifold-mounted
• Valve Function: Two position double solenoid
• Voltage: 12Vdc
• Weight: 0.005 lbs
• Width: 0.4 in.

These double acting single rod stainless steel cylinders are a solid choice when you want air actuated motion. These cylinders have a strong 0.75 in. thick bore and are available in multiple stroke lengths.

Specifications

• Bore: 3/4 in.
• Manufacturer: SMC
• Manufacturer Part #: NCME075-[stroke length]
• Nose Thread: 5/8-18
• Pivot Point: Rear
• Port(s): 1/8 in. NPT
• Retracted Overall Length: 6.5 in., 8.5 in., 10.5 in., 11.5 in.
• Rod Thread: 1/4-28
• Stroke: 2 in., 4 in., 6 in., 7 in.

Documents

CAD File(s)

am-2034_2.STEP

am-2034_4.STEP

am-2034_6.STEP

This is a brass relief valve used in low-volume air tanks and pumps to retard excessive pressure buildup.

Specifications

• Port: 1/8 NPT
• Pressure Range: 25 to 250 psi
• Relief Tolerance: +/- 3%
• Seat Leakage: Bubble Tight Within 10% for Set Pressure Greater Than 50 psi
• Weight: 0.064 lbs

This is a blank cover fitting in where a valve would mount on the CKD manifold (am-3982). All 4 ports of the manifold are required to be covered by either a solenoid or by this cover.

Specifications

• Material: Plastic
• Maximum Pressure: 125 psi
• Style: Manifold-mounted
• Weight: 0.01 Lbs
• Width: 0.4 in.

040.5-R Bimba Cylinder

These double acting single rod stainless steel cylinders are a solid choice when you want air actuated motion. These cylinders have a strong 0.75 in. thick bore and are available in multiple stroke lengths.

These double acting single rod stainless steel cylinders are a solid choice when you want air actuated motion. These cylinders have a strong 0.75 in. thick bore and are available in multiple stroke lengths.

These double acting single rod stainless steel cylinders are a solid choice when you want air actuated motion. These cylinders have a strong 0.75 in. thick bore and are available in multiple stroke lengths.

VIAIR 330C-IG Compressor (air pump) is developed to fill air resovior tanks and features a heat dissipating head. These products are used on mobile competition robots and outdoor equipment.