Panier

filtres

Menu personnel

préférences

Rechercher

PrécédentShort 1/2"Keyed Output Shaf...

SuivantToughbox Series 3/8" Hex Cl...

Split Collar Clamp 1/2 in. Hex HD

Soyez le premier a tester ce produit

This new custom designed collar clamp has been designed specifically with FIRST Robotics Competition teams in mind. This product is Out of Stock until Mid March

# Pièce: am-1526

$5.50

Disponibilité: 186 en stock

Quantité:

Aperçu
Commentaires

This one-piece collar clamp is a nice fractional 1/2" width to make shaft stackups easy. The clamping force is provided by a 10-32 socket head screw, which is bigger than most used in the competition marketplace for a high-strength clamping solution that shouldn't strip out when you need it most. You can replace the 10-32 screw if it becomes lost, with the screws historically used in the AM14U family of chassis. These thoughtfully designed collar clamps also have small bosses on each side. These allow these collar clamps to be installed directly adjacent to an FR8ZZ Round or FR8ZZ Hex bearing without rubbing on the outer races for smooth operation.

Bore: 0.5 in. Hex
Material: 6061 T6 Aluminum
Outside Diameter: 1.25 in.
Thickness: 0.5 in.

Écrivez votre propre commentaire

Le produit peut être examinée que après l'achat
Seul les utilisateurs enregistrés peuvent écrire une critique

Titre du commentaire:

texte du commentaire:

Notation:

Mal
Excellent

A également acheté

Bearing, 1/2 inch Hex Bore, Flanged, (FR8ZZ-HexHD)

#am-2986

$8.00

(87 En stock)

This is a Heavy Duty Hex Bearing which outperforms our previous 1/2" Hex Bearings as it has a Heavy Duty Inner Race. This FR8ZZ-HexHD bearing, 1/2" hex bore, flanged, heavy duty inner race, shielded ball bearing, has an inner race that is thicker and stronger than our recent offering of a similar bearing (am-0279). This bearing has more material between the corners of the hex bore and the edge of the race making it stronger and much less likely to crack under high load.

This bearing is guaranteed to have a stronger, thicker race. 100% of these bearings have been quality checked for a smooth fit over 1/2" hex stock here at AndyMark. Many of our long-time customers will recognize this bearing, as it is the same version we sold back in 2008-2011, and we did not have any failures. Now, it is renamed and quality checked for your high load needs - including drive chassis with cantilevered wheels.

Specifications:

Inside diameter: 0.500-0.502 inch hex bore
Outside diameter: 1.125 inch
Flange thickness: 0.062 inch
Overall thickness: 0.312 inch
Weight: 0.05 pound

#10-32 x 1.5" SHCS - Min 25

#am-1014

$0.38

(En stock)

Statistics:

Material: Steel
Coating: Zinc plated
Thread: #10-32
Length: 1-1/2 inch
Head: Socket Head Cap Screw

1/4-20 x 0.5" BHCS - Min 25

#am-1039

$0.50

(800 En stock)

Specifications:

Material: Steel
Coating: Zinc plated
Thread: 1/4-20
Length: 1/2"
Head: Button Head Cap Screw

10-32 Nylock Jam Nut

#am-1063

$0.11

(325 En stock)

Must be ordered in mulitples of 25

10-32 Nylock Nut

#am-1042

$0.08

(En stock)

This item can only be purchased in multiples of 25

Specifications:

Material: Steel
Coating: Zinc Plated
Thread: #10-32
Thickness: 0.249"
Thread: Fine
Thread Size: 32
Type: Nylon Insert Lock Nut
Wrench Size: 3/8"

2" Compliant Wheel, 1/2 inch Hex, 35 Durometer Green

#am-3462_green

$8.00

(72 En stock)

Compliant wheels are not intended for moving robots, but moving objects. Compliant wheels give way to allow rigid objects to be manipulated easily. A line of multiple wheels on a driven hex shaft creates a very effective roller that ignores variations in the objects being driven. This makes for high-performance intakes and internal conveyors. The wheels are sized for an interference fit and tend to stay in place on a shaft, though a shaft collar may be used to make absolutely sure the wheels stay clear of other mechanisms or maintain consistent spacing.

The hex bore versions of this wheel are undersized, and are intended to be an interference fit on their respective hex shafts. This interference fit allows for effective torque transfer from the hex shaft to the wheel, as well as allowing the wheel to remain in place along the shaft without the need for spacers or collar clamps:

Compliant Wheel Sizing

Different durometer ratings give each wheel unique characteristics. Green wheels (35A durometer) are the softest and most compliant around objects, while orange (40A), maroon (45A), and blue (50A) wheels are increasingly firm. The increased firmness also allows the latter wheels to carry a higher RPM rating. Check out the downloads tab for a chart showing wheels and their maximum RPM.

Specifications

Bore: 1/2 in. Hex, 3/8 in. Hex, Nub Bore
Diameter: 2 in.
Durometer: 35A (Green), ⠀40A (Orange), ⠀45A (Maroon), ⠀50A (Blue), 60A (Black)
Hole Pattern: Qty 2 3.5 mm Holes on a 16 mm Circle for 8 mm bore wheels
Material: TPU
Maximum RPM: 6000 - 9000
Weight: 0.035 lb.
Width: 0.5 in.

Documents

Layout Print(s)

am-3571 2IN 375 Hex Compliant Wheel REV3.PDF

am-3462 2IN 500Hex Compliant Wheel REV3.PDF

am-3572 2IN 8mm Compliant Wheel REV4.PDF

CAD File(s)

am-3571 2IN 375Hex Compliant Wheel REV2.STEP

am-3572 2IN 8mm Compliant Wheel REV2.STEP

am-3462 2IN Molded 500Hex Compliant Wheel REV2.STEP

Additional File(s)

2 inch Compliant Wheel Expansion.pdf

Don't see what you need?

1/4-20 Nylock Nut

#am-1015

$0.11

(500 En stock)

Specifications:

Material: Steel
Coating: Zinc plated
Thread: 1/4-20
Width across hex: 7/16"

10-32 x 0.375 in. Socket Head Cap Screw

#am-1359

$0.30

(250 En stock)

This item can only be purchased in multiples of 25

Specifications

Drive: 5/32 in. Hex
Finish: Zinc
Head: Socket Cap
Length: 0.375 in.
Material: Alloy Steel
Thread: 10-32 Fine
Weight: 0.005 lbs

1/2 in. Hex Collar Clamps, Silver Thin (0.25in) - 1 part

#am-1635

$6.95

(39 En stock)

These custom designed collar clamps have been designed specifically with FIRST Robotics Competition teams in mind. The one-piece collar clamp is a nice fractional 1/2 in. width to make shaft stackups easy. The clamping force is provided by a 10-32 socket head screw, which is bigger than most used in the competition marketplace. This provides a high-strength clamping solution that shouldn't strip out when you need it most. You can even replace the 10-32 screw if it becomes lost with the screws historically used in the AM14U family of chassis. These thoughtfully designed collar clamps also have small bosses on each side. This allows these collar clamps to be installed directly adjacent to an FR8ZZ Round or FR8ZZ Hex bearing without rubbing on the outer races for smooth operation.

90 Degree Gusset

#am-3860

$5.00

(44 En stock)

We are pleased to offer these new gussets that are suitable for 1" based building systems. These thoughtfully designed gussets are made from 1/8" thick 6061-T6 aluminum, which is a much stronger material than other 0.09" 5052 gussets. All of these framing gussets feature a 1" linear hole pattern, with holes suitable for either #10 screws or 3/16" rivets.

On all of the angle gussets, a generous radius was used on the inside corner for maximum strength. The various angle gussets, along with the quad and tee gusset are used together to create structures and sub-assemblies for your robot. Our bearing and Sport gussets are perfect building blocks to create a massive variety of mechanisms and assemblies to suit your needs.