Gearboxes
This bearing plate is a great way to mount a 0.875 in. OD (FR6) bearing into thin or weak material that otherwise could not tolerate or support a press-fit.
Specifications:
Bimba Air Cylinder, Spring extended with appropriate nut.
Specifications:
This is a 0.5 in. Hex output shaft with a 57 Sport mounting. We suggest using our red tacky grease, am-2768. We encourage that the user powers the gearbox continuously for 30 minutes without grease to allow the gear teeth to wear in. While we do design with short run times in mind, this 'run in' period for smooth gearbox operation, is recommended. Once this is completed, thoroughly grease the gear teeth periodically to ensure smooth operation.
The LJ Bevel Box is a right angle gearbox using steel bevel gears, designed to integrate with a CIM Motor (am-0255), CIM-Sim (am-0932), 57 Sport, or CIM Sport. This setup allows for the use of a gearbox or CIM motor in locations where you many not have the space available for an assembly in a straight line. We recommend using this gearbox in low torque setups. An E4T encoder can be added to the side of this gearbox, but is not included.
This is the aluminum motor mount plate for our 3 Motor Toughbox. A standard
Toughbox could be converted to a 3 Motor Toughbox by using this plate and also
the 3 Motor Toughbox Shaft Plate.
Specifications:
This is the aluminum shaft plate for our 3 Motor Toughbox. A standard
Toughbox could be converted to a 3 Motor Toughbox by using this plate and also
the 3 Motor Toughbox Motor Plate.
Specifications:
This 35 tooth gear and 6mm Collar Clamp is intended to be installed onto a
NeveRest Motor (am-3104) without any gearbox or pinion attached to the motor
shaft. This gear can also be used with any motor with a 0.125 in. output shaft.
Individual Components within Kit:
Specifications:
This 40 tooth gear and 6mm Collar Clamp is intended to be installed onto a
NeveRest Motor (am-3104) without any gearbox or pinion attached to the motor
shaft. This gear can also be used with any motor with a 0.125 in. output shaft.
Individual Components within Kit:
Specifications:
This 45 tooth gear and 6mm Collar Clamp is intended to be installed onto a
NeveRest Motor (am-3104) without any gearbox or pinion attached to the motor
shaft. This gear can also be used with any motor with a 0.125 in. output shaft.
Individual Components within Kit:
Specifications:
This kit is the needed hardware to attach an RS 775 motor such as our RedLine
(am-3775) to a 57 Sport Gearbox.
Specifications:
Individual Components within this Bundle:
This is a high-strength aluminum hex shaft, with 1/2" width across flats,
designed to be used with E4T encoders. This product works well with the Modulox
Encoder Back Block.
Specifications:
Sometimes, you just need a winch! Our Afterburner Winch Kit mounts easily to the Rocketbox PTO to provide an additional 15:24 reduction and a ~1.5in. winch drum for your robot's needs. This winch bolts onto the the RocketBox and interfaces with the Mechanism Output Shaft of the gearbox via a sprocket and chain reduction to provide a winching solution for various mechanisms. This winch also features an integrated lock-out plate and cylinder to create a locking, non-backdrivable winch solution. This allows your robot to save weight by using your drive motors for high-load tasks like retracting a climber or cocking back a shooter in situations where you don't need to drive at the same time. You can also pop in 2 hex bearings and drive the input sprocket with any hex shaft.
This new kit features the 4 tooth dog found in the EVO with a new 4 tooth lockout plate, as well as a pre-made chain loop so that this is as fully assembled as possible letting you hit the ground running as soon as you open the box.
CAD File(s)
am-3344a AfterBurner Winch Kit with 4 Tooth Dog.STEP
Layout Print(s)
This is the Carrier Plate w/ Sun Gear for the AM Planetary gearbox. Five
planet gears (not included) ride on the dowel pins pressed into this part.
Referencing the picture above, those dowel pins are protruding out the bottom
side of the carrier plate.
Specifications:
3/8 in. wide, steel hex shaft
Specifications:
Sheet Aluminum Plate for back side of the Work Gearbox.
Specifications: