4" HiGrip Wheel, 50A Durometer Blue

This is a Trilobe, thread forming, or thread rolling screw, ideal for applications where the screw is being threaded into plastic or metal. 

A flat washer is part of the 5/16 hex head, providing more surface area contact than a regular hex head. The increased bearing area decreases the likeliness of crushing mating surfaces. Trilobe, or Thread Rolling, screws have a blunt tapered point that requires a pre-drilled or punched hole; eliminates chips and permits replacement with standard screw. Zinc plating froms a zinc carbonate film that greatly retards the corrosion rate in a normal atmosphere, which is similar to the aluminum oxide film that forms on aluminum that accounts for its low corrosion rate. 

Product Overview:

• Quantity: 50
• Diameter: #10
• Finish: Zinc
• Head: 5/16 Hex with integral washer
• Thread Length: 3/4"
• Material: Steel
• Thread Size: 10-24
• Thread Type: Trilobe, Thread Rolling
• Weight per Screw: 0.007 lbs
• Package Weight: 0.34 lbs

Each hub now has a "flower" pattern that fits and keys into our 42T 5 mm HTD Pulley, which means you are no longer constrained to our legacy 500EX Hex Hub for compatibility with this pulley. Every hub still maintains a closed-profile hole for maximum strength. Every shaft hub has been designed with bearing bosses on both sides that have been sized appropriately for the mating bearings that would pair with the bore through the hub, which means you can run each hub right against a bearing with no need for extra spacers. All of these hubs are also made from 7075-T6 aluminum, which is much stronger than the previously used 6061-T6, 6005, and 6105 alloys from our older designs. Where possible, the shoulder on shaft hubs was reduced to 7/8" in diameter for an easier fit with our molded plastic wheels, while still maintaining a precise 1.125" diameter boss for locating in wheels, sprockets, gears, and more. 

The holes are evenly spaced on a 1.875 in. circle and 0.201 inches in diameter. That's a perfect size for #10 bolts!

Learn how to attach these hubs to AndyMark wheels by watching this video!

This updated version of the AndyMark 775 RedLine Motor is an even faster and more powerful version of this popular 775-class motor platform. With a power rating of up to 363W, this motor is capable of delivering even more immense power in the same small lightweight package over the previous version. This ball-bearing supported, air cooled motor is best used in high-speed applications where the motor will not be stalled for long periods such as shooters, conveyors, and intake mechanisms. With sufficient care and attention to your application's traction limit, this motor can be effective in FRC drive applications as well.

This variation of the RedLine comes with a 16 tooth, 0.7 Module pinion and mounting screws (am-3768) already installed allowing this motor to be installed into either a 57 Sport or a Dual 775 Sport gearbox. Not only does this take the risk of damaging the motor during pinion installation out of your hands, it also means that this counts as a COTS part in FRC.

The 57 Sport is a competition tested high performance line of planetary gearboxes from AndyMark and BaneBots. The 57 Sport features numerous improvements over previous planetary gearboxes used on FIRST Robotics Competition robots. 

Do you have a hard time finding some strong hex stock aluminum? We have it! This is 7075 series aluminum, which is great for use in transmission shafts.

Specifications:

• Material: 7075 Aluminum
• Width: 1/2" hex (0.496-0.499 inches)
• Weight: 0.27 pounds/ft
• Length: You specify, 1 foot, 3 feet or 6 foot in length, +/- 1"

Sourcing the right stock for the right job can be hard sometimes. No longer is that true for 1/2 inch hex spacer stock! Offered in precisely machined 1.2 inch sections as well as one three and six foot lengths (plus or minus 0.125".) This rigid stock can be cut and used in any assembly you can think of. Gearbox design? Yup. Drive train design? Yep. Manipulator design? Yep! Why stop a spacers, you can even use it to couple 2 shafts together and transfer crazy amounts of torque or cover it in grippy material and use it as a game piece roller.