Close
Main Categories
    Filters
    Preferences
    Search

    Shafts, Adapters & Collars

    Shafts, Adapters & Collars

    View as Grid List
    Sort by
    Display per page

    0.375"Aluminum Hex Stock 1 Foot (am-3807-1)

    #am-3807-1
    $10.00 $6.08
    (In stock)

    This 7075 T6 Aluminum shaft stock is 0.375 in. from flat to flat. This stock may be a tight fit in some of our 3/8 in. hex products.

     

    Specifications

    • Length: You specify
    • Material: 7075-T6 Aluminum
    • Weight: 0.25 lbs/ft
    • Width: 0.375 in. Hex

    3/8 in. 7075 Aluminum Hex Shaft Stock - 3 Ft Length

    #am-3807-3
    $21.00 $15.63
    ( 5 In stock)

    This 7075 T6 Aluminum shaft stock is 0.375 in. from flat to flat. This stock may be a tight fit in some of our 3/8 in. hex products.

     

    Specifications

    • Length: You specify
    • Material: 7075-T6 Aluminum
    • Weight: 0.25 lbs/ft
    • Width: 0.375 in. Hex

    3/8 in. 7075 Aluminum Hex Shaft Stock - 6 Foot Length

    #am-3807-6
    $37.00 $31.25
    (In stock)

    This 7075 T6 Aluminum shaft stock is 0.375 in. from flat to flat. This stock may be a tight fit in some of our 3/8 in. hex products.

     

    Specifications

    • Length: You specify
    • Material: 7075-T6 Aluminum
    • Weight: 0.25 lbs/ft
    • Width: 0.375 in. Hex

    0.5 in. Round Thin Line Collar Clamp

    #am-3792
    $6.92 $7.82
    ( 0 In stock)

    This collar clamp is a one-piece shaft collar with a 1/2 in. bore, 0.984 in. OD, and 0.236 in. width. The thin line design reduces weight and allows for use in confined spaces. It has the clamp style benefits of not marring the shaft, easy removability, and indefinite adjustability while commonly being used for guiding, spacing, stopping, mounting, and component alignment.

    Specifications:

    • Material: 2024 Aluminum
    • Bore: 0.500 in.
    • Outside Diameter: 0.984 in.
    • Thickness: 0.236 in.
    • Weight: 0.017 Pounds
    • Clamping Screws: M2 5x8 SHCS

    0.5"Hex Adapter Shaft for Bosch Motor

    #am-3723
    $15.38 $17.36
    (In stock)

    This is an adapter to convert the female spline output of the Bosch Seat Motor (am-3493) to a 2 inch long 0.5 inch hex shaft. The square end interfaces with the female spline of the motor and is retained by an included 6-32 screw and washer. Our testing shows that in a back-drive situation the worm gear in the gearbox will fail before the motor spline or this adapter. 

    Specifications: 

    • Overall Length: 3.014 in.
    • Hex Length: 2.0 in.
    • Hex Width: 0.5 in.
    • Square Width: 0.23 in.
    • Weight: 0.126 Pounds
    • Material: 4140 Steel

    Included Hardware:

    • 1 - 6-32 x 0.5 in. Hex Head Machine Screw - (Sold in a Bulk Qty as am-1436)
    • 1 - #6 x 0.375" OD Flat Washer

    0.50 in. Hex and Keyed Shaft Coupling

    #AM-1560
    $25.00
    ( 5 In stock)

    Whether you have shafts that are too short or shafts of different types, this coupling will solve every component connection issue you've had! Need to combine multiple hex shafts, multiple 1/2-inch keyed shafts, or convert between hex and keyed? This coupling solves all at a better price than anyone else can offer!

    Shaft Compatability

    This coupling has geometry to capture 0.50-inch hex shafts with an inside hex of 0.51 to 0.52 inches as well as 0.5 inch keyed shafts with a 1/8th inch keyway with a keyway width of 0.128 inches to 0.131 inches.

    0.50 in. Hex to 0.375 in. Hex Adapter

    #am-3832
    $12.30 $13.89
    (In stock)

    This lightweight aluminum adapter allows conversion of 0.375 inch hex shafts into 0.500 inch hex shafts or 0.500 inch hex holes into 0.375 inch hex holes. This component is not recommended for extremely high torque applications.

    Specifications:

    • Material: 6061 Aluminum
    • OD: 0.499 in. Hex
    • ID: 0.376 in. Hex
    • Length: 0.50 in.
    • Weight: 0.004 Pounds

    1/2" Diameter Steel Shaft stock, 1/8" keyway, 30" long

    #am-2391
    $53.81 $60.77
    (In stock)

    This is a 1/2 inch steel shaft with a 1/8 inch keyway machined on the entire length.

    Specifications:

    • Material: Carbon steel (AISI-1045)
    • Diameter: 0.499-0.500 inch
    • Keyway width: 0.125-0.127 inch
    • Weight: 1.56 pounds
    • Length: 30 inches +/- 1/4"

    3/8" diameter steel shaft stock, 3/32" keyway, 30" long

    #am-2392
    $55.35 $62.51
    ( 0 In stock)

    This is a 3/8 inch steel shaft with a 3/32 inch keyway machined on the entire length.

    Specifications:

    • Material: Carbon steel (AISI-1045)
    • Diameter: 0.374-0.375 inch
    • Keyway width: 0.093-0.095 inch
    • Weight: 0.89 pound
    • Length: 30 inches +/- 1/4"

    8mm to 1/2" Key Shaft Adapter

    #am-0472
    $18.45
    ( 0 In stock)

    0.500 inch shaft with 1/8 inch keyway and 0.313 (8mm), 2mm keyed bore The bore of this adapter fits onto the 2.5" CIM Motor 

    WARNING: There is only a 0.016 inch thick wall of steel between the bottom of the 1/8" keyway and the 0.313" bore. 

    Specifications:

    • Material: AISI-1045 steel
    • Outside diameter: 0.497 - 0.499 inch
    • Length: 0.75 "
    • Keyway: 0.128 " wide
    • Bore: 0.313 " with 2mm (.08") keyway
    • Weight: 0.03 Lb

    Aluminum Hex Shaft Stock, 1/2" width, 7075 1'

    #am-2291-1
    $25.00 $13.89
    ( 7 In stock)

    Do you have a hard time finding some strong hex stock aluminum? We have it! This is 7075 series aluminum, which is great for use in transmission shafts.

     

    Specifications:

    • Material: 7075 Aluminum
    • Width: 1/2" hex (0.496-0.499 inches)
    • Weight: 0.27 pounds/ft
    • Length: You specify, 1 foot, 3 feet or 6 foot in length, +/- 1"

    Aluminum Hex Shaft Stock, 1/2" width, 7075 3'

    #am-2291-3
    $45.00 $27.78
    ( 28 In stock)

    Do you have a hard time finding some strong hex stock aluminum? We have it! This is 7075 series aluminum, which is great for use in transmission shafts.

     

    Specifications:

     

    • Material: 7075 Aluminum
    • Width: 1/2" hex (0.496-0.499 inches)
    • Weight: 0.27 pounds/ft
    • Length: You specify, 1 foot, 3 feet or 6 foot in length, +/- 1"

    Aluminum Hex Shaft Stock, 1/2" width, 7075 6'

    #am-2291-6
    $89.00 $52.09
    ( 20 In stock)

    Do you have a hard time finding some strong hex stock aluminum? We have it! This is 7075 series aluminum, which is great for use in transmission shafts.

     

    Specifications:

    • Material: 7075 Aluminum
    • Width: 1/2" hex (0.496-0.499 inches)
    • Weight: 0.27 pounds/ft
    • Length: You specify, 1 foot, 3 feet or 6 foot in length, +/- 1"

    Collar Clamp, 1/2 Hex Bore, 2 Pc with Flats

    #am-2871
    $12.68 $14.32
    ( 0 In stock)

    This novel style of collar clamp is split into two pieces so that it can be attached without removing any shafts. The bore is a 1/2" hex. The flats on the perimeter allow for the collar clamp to be held in position or turned for better assembly control. 

    This clamp has been designed and fabricated by BaneBots, and proudly sold through AndyMark.

    Specifications:

    • Material: Aluminum
    • Bore: hex hole, 1/2 inch
    • Outside Diameter: 0.94 inch
    • Thickness: 0.375 inch
    • Width Across Flats: 7/8 inch
    • Weight: 0.020 pound
    • Clamping Screws: #6-32 x 1/2" long (qty. 2)

    Plastic spacers are included with this clamp, positioned between the two halves. These are to be removed before usage.

    Collar Clamp, 1/2" Bore, Aluminum

    #am-2099
    $6.15 $6.95
    (In stock)

    Aluminum Clamp On Shaft Collar, 1/2" Bore 

    Specifications:

    • Material: Aluminum
    • Diameter: 1.125 inches
    • Inside Diameter: 0.500 inches
    • Thickness: 0.410 inches
    • Weight: 0.034 pounds

    Collar Clamp, 3/8 Bore, 2 Pc with Flats

    #am-2867
    $8.46 $9.56
    (In stock)

    This novel style of collar clamp is split into two pieces so that it can be attached without removing any shafts. The bore is a 3/8" round hole . The flats on the perimeter allow for the collar clamp to be held in position or turned for better assembly control. 

    This clamp has been designed and fabricated by BaneBots, and proudly sold through AndyMark.

    Specifications:

    • Material: Aluminum
    • Bore: round, 3/8 inch
    • Outside Diameter: 0.94 inch
    • Thickness: 0.375 inch
    • Width Across Flats: 7/8 inch
    • Weight: 0.023 pound
    • Clamping Screws: #6-32 x 1/2" long (qty. 2)