10 Feet - Red 4 AWG Flexible Silicone Jacketed Wire

Looking to expand your robot battery cables? Well 4 AWG just may be the answer for you. The larger wire gauge provides less resistance and therefore can prolong your battery life. Just hooking up cable straight to a battery is not recommended, which is where this connector kit comes in. This SB120 Connector handles 48V and provides a quick connect and disconnect from battery to robot.

Specifications

• Gauge: 4 AWG
• Material: Red Plastic, Copper
• Weight: 0.2 lbs

REEFSCAPE℠ game piece pre-orders are not eligible for a return, nor can the order be combined to ship with other  products or orders. Payment methods for the pre-orders cannot be changed after payment has been received. If a pre-order is canceled prior to shipping, store credit is the only refund option available.

This black 4 AWG wire is silicone jacketed, making it incredibly flexible and a great choice for your FRC robot's batteries.

Comes in spools of 10 feet each. This wire consists of .08mm tinned copper with a strand count of 5000.

There are 60 RGB LEDs per meter, and you can control each LED individually! You can set the color of each LED's red, green and blue component with 8-bit PWM precision (24-bit color per pixel). 

The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 digital output pin are required to send data down. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you

It comes as a full 8.2ft (2.5m) strip and can be separated at each junction between LEDs for customization. Add in a couple connectors and you can separate sections and still control them all together.

Specifications:

• WS2812b chip (WS2811 IC built in SMD5050)
• 60 LEDs per Meter (150 Individually addressable RGB LEDs on the 8.2 ft section)
• Maximum 5V @ 60mA draw per 1.3" strip segment which has 2 LEDs on it (both LEDs on full brightness)
• Maximum 5V @ 4.5A draw for entire strip (Entire strip on full brightness)
• Power: 15 Watts
• Rated Life: 50000 Hours
• 5VDC power requirement (do not exceed 6VDC) - no polarity protection
• 1 integrated RGB LEDs per segment, individually controllable
• LED wavelengths: 630nm/530nm/475nm

The MK ES17-12, 12 Volt, 18 amp-hour sealed lead acid battery with nut and bolt connector has proven to be a trustworthy power source for many FIRST Robotics Competition robots. 

The batteries will be packed within a 7"x7"x7" box (aka: interior box). A 3/4" layer of closed-cell foam will be packed around the interior box, within a 9"x9"x9" box. The entire weight of this double box packing assembly will be approximately 29 pounds.

Two (2) batteries are shipped within one box for this price.

These bearing options are perfect for supporting spline shafts. The bearings slide on easily in our testing.

Flanged version: 35mm ID x 47mm OD x 7mm overall width - 1.5mm thick flange - .070 lbs

Radial version: 35mm ID x 47mm OD x 7mm overall width - .065 lbs

Comes in both radial and flanged versions.

This bonded black and red 12 AWG wire is silicone jacketed, making it incredibly flexible and a great choice for your FRC robot's motors.

Comes in spools of 50 feet each. This wire consists of .08mm tinned copper with a strand count of 680. Spool weight is 3.4 pounds.

This bonded wire cleanly separates and leaves no residue on the opposite wire when split.

This is a 1.5" thick 45A durometer urethane wheel with a half inch hex bore. Great for accelerating game objects or for when low compression is desired. 4 inch outer diameter.

This bonded black and red 18 AWG wire is silicone jacketed, making it incredibly flexible and a great choice for your FRC robot's compressor.

Comes in spools of 25 feet each. This wire consists of .08mm tinned copper with a strand count of 150. Spool weight is .43 pounds.

This bonded wire cleanly separates and leaves no residue on the opposite wire when split.

Note: The Sliding Elevator Bearing Block kit plates have been updated for 2024 to improve the ability to mount to grid pattern tubing. The threaded holes have also been changed to 1/4-20 to utilize a thicker bolt for the side bearings.

Full kit weight: .75 pounds - 1 bearing block + hardware and bearings weighs 3 ounces.

The Sliding Elevator Bearing Block Kit provides enough hardware to build up one stage of a sliding 2" x 1" box extrusion elevator.

For every stage in your elevator's design, add another kit.

1 stage elevator = 1 kit

2 stage elevator + carriage = 2 kits