Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Boîtes de vitesses

    Boîtes de vitesses
    Voir comme Grille Lister
    Trier par
    Affichage par page

    0.875"Bearing Plate (am-3721)

    #am-3721
    $9.95
    (9 En stock)

    This bearing plate is a great way to mount a 0.875 in. OD (FR6) bearing into thin or weak material that otherwise could not tolerate or support a press-fit.

    Specifications:

    • Material: 5052 Aluminum
    • Bore: Press fit for FR6 bearing
    • Thickness: 0.125 in.
    • Bolt Pattern: 4x clearance for #10-32 on 2.00 in. circle
    • Length: 1.875 in.
    • Width: 1.875 in.
    • Weight: 0.032 Pounds

    040.5-RP Bimba Air Cylinder, spring extend w/ nut (am-0591)

    #am-0591
    $49.00

    Bimba Air Cylinder, Spring extended with appropriate nut.

    Specifications:

    • Manufacturer: Bimba Inc.
    • Type: Single Acting - Spring Extend (shaft is out in normal position)
    • Bore: 3/4"
    • Stroke: 1/2"
    • Pivot Type: Nose mount and Rear mount
    • force to overcome spring: 6 pounds
    • Threaded Rod End: 1/4-28
    • Port Size: 1/8" NPT
    • Threaded Nose Size: 5/8-18 (5/8-18 nut included)
    • Weight: 0.244 lbs

    1:1 LJ Bevel Box with 0.5" Hex Output Shaft and 57 Sport Mounting

    #AM-3840_SPORT
    $169.13
    (0 En stock)

    This is a 0.5 in. Hex output shaft with a 57 Sport mounting. We suggest using our red tacky grease, am-2768. We encourage that the user powers the gearbox continuously for 30 minutes without grease to allow the gear teeth to wear in. While we do design with short run times in mind, this 'run in' period for smooth gearbox operation, is recommended. Once this is completed, thoroughly grease the gear teeth periodically to ensure smooth operation.

    1:1 LJ Bevel Box with 0.5"Hex Output Shaft and CIM Mounting

    #AM-3840_CIM
    $175.28
    (0 En stock)

    The LJ Bevel Box is a right angle gearbox using steel bevel gears, designed to integrate with a CIM Motor (am-0255), CIM-Sim (am-0932), 57 Sport, or CIM Sport. This setup allows for the use of a gearbox or CIM motor in locations where you many not have the space available for an assembly in a straight line. We recommend using this gearbox in low torque setups. An E4T encoder can be added to the side of this gearbox, but is not included.

    3 Motor Toughbox Motor Plate (am-2387)

    #am-2387
    $23.89
    (En stock)

    This is the aluminum motor mount plate for our 3 Motor Toughbox. A standard Toughbox could be converted to a 3 Motor Toughbox by using this plate and also the 3 Motor Toughbox Shaft Plate.

    Specifications:

    • Size: 5x5x0.25 inches
    • Material: 6061 Aluminum
    • Weight: 0.528 pound
    • Finish: Tumbled

    3 Motor Toughbox Shaft Plate (am-2386)

    #am-2386
    $21.53
    (En stock)

    This is the aluminum shaft plate for our 3 Motor Toughbox. A standard Toughbox could be converted to a 3 Motor Toughbox by using this plate and also the 3 Motor Toughbox Motor Plate.

    Specifications:

    • Size: 5x5x0.125 inches
    • Material: 6061 Aluminum
    • Weight: 0.274 pound
    • Finish: Tumbled

    3/16" Diameter Shoulder Screw (am-0090)

    #am-0090
    $7.17
    (En stock)
    3/16" dia shoulder screw am-0090

    35 Tooth NeveRest Pinion and 6mm Collar Clamp (am-3682)

    #am-3682
    $21.53
    (En stock)

    This 35 tooth gear and 6mm Collar Clamp is intended to be installed onto a NeveRest Motor (am-3104) without any gearbox or pinion attached to the motor shaft. This gear can also be used with any motor with a 0.125 in. output shaft.

    Individual Components within Kit:

    • 1 - Collar Clamp, 6mm (am-3473)
    • 1 - 35 Tooth, NeveRest Pinion (am-3201)

    Specifications:

    • Bore: 0.124-0.127 in.
    • Weight: 0.084 Pounds
    • Material: 4140 Steel
    • Thickness: 0.236 in.
    • Tooth Count: 35
    • Pitch Diameter: 1.09 in.
    • Pressure Angle: 20
    • Diametral Pitch: 32

    40 Tooth NeveRest Pinion and 6mm Collar Clamp (am-3683)

    #am-3683
    $21.53
    (En stock)

    This 40 tooth gear and 6mm Collar Clamp is intended to be installed onto a NeveRest Motor (am-3104) without any gearbox or pinion attached to the motor shaft. This gear can also be used with any motor with a 0.125 in. output shaft.

    Individual Components within Kit:

    • 1 - Collar Clamp, 6mm (am-3473)
    • 1 - 40 Tooth, NeveRest Pinion (am-3202)

    Specifications:

    • Bore: 0.124-0.127 in.
    • Weight: 0.108 Pounds
    • Material: 4140 Steel
    • Thickness: 0.236 in.
    • Tooth Count: 40
    • Pitch Diameter: 1.25 in.
    • Pressure Angle: 20
    • Diametral Pitch: 32

    45 Tooth NeveRest Pinion and 6mm Collar Clamp (am-3684)

    #am-3684
    $26.14
    (En stock)

    This 45 tooth gear and 6mm Collar Clamp is intended to be installed onto a NeveRest Motor (am-3104) without any gearbox or pinion attached to the motor shaft. This gear can also be used with any motor with a 0.125 in. output shaft.

    Individual Components within Kit:

    • 1 - Collar Clamp, 6mm (am-3473)
    • 1 - 45 Tooth, NeveRest Pinion (am-3203)

    Specifications:

    • Bore: 0.124-0.127 in.
    • Weight: 0.132 Pounds
    • Material: 4140 Steel
    • Thickness: 0.236 in.
    • Tooth Count: 45
    • Pitch Diameter: 1.40 in.
    • Pressure Angle: 20
    • Diametral Pitch: 32

    57 Sport 775 Motor Mounting Kit (am-3768)

    #am-3768
    $8.46
    (En stock)

    This kit is the needed hardware to attach an RS 775 motor such as our RedLine (am-3775) to a 57 Sport Gearbox.

    Specifications:

    • Gear Bore: 5 mm
    • Gear Material: Steel

    Individual Components within this Bundle:

    • 1 - RS-775 Motor Pinion Gear (am-3784)
    • 2 - M4 x 8 mm SHCS
    • 2 - M4 Lock Washer

    AfterBurner Winch

    #am-3344a
    $350.00

    Sometimes, you just need a winch! Our Afterburner Winch Kit mounts easily to the Rocketbox PTO to provide an additional 15:24 reduction and a ~1.5in. winch drum for your robot's needs. This winch bolts onto the the RocketBox and interfaces with the Mechanism Output Shaft of the gearbox via a sprocket and chain reduction to provide a winching solution for various mechanisms. This winch also features an integrated lock-out plate and cylinder to create a locking, non-backdrivable winch solution. This allows your robot to save weight by using your drive motors for high-load tasks like retracting a climber or cocking back a shooter in situations where you don't need to drive at the same time. You can also pop in 2 hex bearings and drive the input sprocket with any hex shaft. 

     

    This new kit features the 4 tooth dog found in the EVO with a new 4 tooth lockout plate, as well as a pre-made chain loop so that this is as fully assembled as possible letting you hit the ground running as soon as you open the box. 

     

    Documents

     

    CAD File(s)

    am-3344a AfterBurner Winch Kit with 4 Tooth Dog.STEP

    Layout Print(s)

    am-3344a AfterBurner Winch Kit 4 tooth Dog.PDF

    AMP Stage Plate (am-2286)

    #am-2286
    $23.06
    (En stock)

    This is the Carrier Plate w/ Sun Gear for the AM Planetary gearbox. Five planet gears (not included) ride on the dowel pins pressed into this part. Referencing the picture above, those dowel pins are protruding out the bottom side of the carrier plate.

    Specifications:

    • Weight: 0.07 pounds
    • Diameter: 1-3/8"
    • Length: 15/16"
    • Tooth Count: 15
    • Diametral Pitch: 32
    • Pressure Angle: 20 degrees
    • Pin Diameter: 0.125"
    • Gear Material: 1117 Steel

    AMS Cluster Hex Shaft (am-0302)

    #am-0302
    $13.84
    (En stock)

    3/8 in. wide, steel hex shaft

    Specifications:

    • Material: 4140 steel
    • Overall length: 2.83 in.
    • Hex width: 0.373 in.
    • Weight: 0.094 pounds

    Back Plate for Worm Gearbox (am-0918)

    #am-0918
    $10.76
    (En stock)

    Sheet Aluminum Plate for back side of the Work Gearbox.

    Specifications:

    • Width: 3.625" (4.563" at tabs)
    • Height: 4.75"
    • Depth: 1.463" at L
    • Material: 6061 Aluminum (.0875" thick)
    • Weight: 0.16 Lb

    CIM Sport Motor Block (am-3770)

    #am-3770
    $15.38
    (En stock)

    This component attaches to a CIM Motor (am-0255) and secures to the housing and input stage for a CIM Sport Gearbox. This motor block does not require modification to the CIM Motor Shaft.

    Specifications:

    • Weight: 0.25 Pounds
    • Material: Aluminum
    • Width: 1.75 in.
    • Height: 1.75 in.
    • Depth: 1.105 in.