Retention Clip for 15/30/45A Powerpole Connectors

Tired of hex clamp collars that cost an arm and a leg? Tired of stripping out the set screw on your clamp collar? Need to add a collar in an assembly and don't want to remove everything from your hex shaft?

Me too! I've ran into all of the above scenarios multiple times building multiple robots. These collars are the holy grail -

• split so they can easily be added or removed
• lightweight 6061 aluminum
• .5 oz (.031 lbs) for one hex collar
• uses two 8-32 socket head cap screws that require a 9/64" allen wrench
• $4.00 per collar, sold in 5 packs
• anodized black for awesomeness

General Dimensions:

• When clamped on 1/2 inch hex shaft - approx 1.2 inch outer diameter
• 0.40 inches wide
• STEP file CAD Model Available

This breakout board is safe to use with the Talon SRX. It does not connect to previous versions of the Talon.


To use existing products teams have 3D-printed custom mounting brackets and had to purchase specialty ribbon cables - all to have only the most basic breakout functions of 1 or 2 features at a time. This board eliminates or simplifies all these issues and provides enhanced functionality while enabling all available Talon features.

Specifications:

• Includes the functionality of several breakout-boards in one
• Direct Mounting to Talon SRX with existing hardware
• No Ribbon Cable Needed
• Header pins allow connectors to be used for sensors (or direct soldered if desired)
• Short-Circuit Protection
• 3.3V & 5V Sensors
• Built-In Pull-Up/Downs (For Limit Switches and Various Encoders)
• Several LEDs for quick sensor/software debugging

This is a Heavy Duty Hex Bearing which outperforms our previous 1/2" Hex Bearings as it has a Heavy Duty Inner Race. This FR8ZZ-HexHD bearing, 1/2" hex bore, flanged, heavy duty inner race, shielded ball bearing, has an inner race that is thicker and stronger than our recent offering of a similar bearing (am-0279). This bearing has more material between the corners of the hex bore and the edge of the race making it stronger and much less likely to crack under high load.

This bearing is guaranteed to have a stronger, thicker race. 100% of these bearings have been quality checked for a smooth fit over 1/2" hex stock here at AndyMark. Many of our long-time customers will recognize this bearing, as it is the same version we sold back in 2008-2011, and we did not have any failures. Now, it is renamed and quality checked for your high load needs - including drive chassis with cantilevered wheels.

Specifications:

• Inside diameter: 0.500-0.502 inch hex bore
• Outside diameter: 1.125 inch
• Flange thickness: 0.062 inch
• Overall thickness: 0.312 inch
• Weight: 0.05 pound

This is an all in one in-line pressure regulator and low pressure side gauge perfect for lightweight pneumatic systems where you need to mount a regulator somewhere downstream in the system.

This is a miniature pressure regulator with 1/4 in. push to connect fittings perfect for lightweight pneumatic systems where you need to mount a regulator downstream in your pneumatics system. Combining push to connect fittings with the miniature regulator makes installation anywhere in your robot fast and simple.  This regulator is significantly reduced in volume and weight compared to the classic regulators used in FRC. This lets you take advantage of every last cubic inch and ounce on your robot.

Specifications

• Depth: 0.98 in
• Height: 2.40 in
• Operating Pressure: 0-150 psi
• Port(s) : (2) 1/4 in. Female Press-In
• Width: 2.15 in

Specifications:

• Number of Teeth: 45
• Pitch Length: 8.86 inches (225mm)
• Pitch: 5mm
• Width: 9mm
• Tooth profile: 5mm pitch HTD
• Weight: 0.1

This is a miniature pressure gauge with two 1/4 in. push to connect fittings for in line installations. It is perfect for lightweight pneumatic systems where you need to mount a pressure gauge in line with a tubing run. This pressure gauge is significantly reduced in volume and weight compared to the classic gauges used in FRC. This lets you take advantage of every last cubic inch and ounce on your robot.

Specifications

• Depth: 0.51
• Height: 1.27
• Operating Pressure: 0-150 psi
• Port(s): (2) 1/4 in. Female Push-in
• Pressure Range: 0-116 psi
• Width: 1.58

This is a kit of loose components to get you from the start line to finish line on your wiring projects. Powerpole PP45 housings in white black and red at a whopping 50 count of each and 150 contacts are included in this bundle.

The contacts are rated for 45 amps, and sized for 10-12 gauge wire. We recommend our crimp tool as the perfect crimp tool for making cables.

The easy way to change the length of your #25 chain. (Chain not included)