Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Hubs

    Hubs

    Voir comme Grille Lister
    Trier par
    Affichage par page

    0.5 in. Hex Hub

    #am-2568
    $15,38
    ( 23 En stock)

    This is the "500EX Hex Hub" the bore is a 1/2" Hex Hole. It is a slightly different version of the 500 Hex Hub. It is manufactured differently, as it is extruded. Also, there is a 1.124" diameter boss on each side of the hub flange, providing a location for 1.125" bore flat sprockets. Are you having a hard time keeping your sprocket concentric with your hub? This hub is the trick.

    This is the hub featured in the 2014 and 2015 Kit of Parts Drive Chassis and fits all AndyMark wheels. 

    Specifications:

    • Material: 6063 Aluminum
    • Bore: 1/2" Hex
    • Bolt Pattern: 0.204" diameter holes, evenly spaced on a 1.875" diameter bolt circle
    • Outside diameter: 2.25"
    • Weight: .088

    10mm DD Bore Hub

    #am-2279
    $26,14
    (En stock)

    This hub fits all AndyMark wheels, and the bore fits the shaft of our Snow Blower Motor. 

    The bolt pattern is designated as 6 holes evenly spaced on a 1.875" diameter bolt circle. The DD broach is consistently cut to be aligned with the holes.

    Specifications:

    • Material: 6061 Aluminum
    • Bore: 10mm (0.394 inch) diameter DD bore, with 0.294 wide (broached)
    • Bolt Pattern: 0.204" diameter holes, evenly spaced on a 1.875" diameter bolt circle
    • Outside diameter: 2.40"
    • Weight: 0.084 pounds
    • Overall width: 0.49 inch

    The mounting holes and the DD bore are now aligned and consistent.

    10mm Key Hub

    #am-0985a
    $16,91
    (En stock)

    This is a 10mm Key Hub. This hub fits all AndyMark wheels. 

    The machine key is not included with the hub.

    Specifications:

    • Material: 6061 Aluminum
    • Bore: 10mm (0.374 inch), with a 4mm (0.157 inch) keyway
    • Bolt Pattern: Six - 0.204" diameter holes, evenly spread on a 1.875" diameter bolt circle.
    • Finish: tumbled
    • Outside diameter: 2.25 inches
    • Weight: 0.11 pound

    375 Hex Hub

    #am-2231a
    $15,38
    (En stock)

    Product Overview: 
    This hub features a .375" Hex bore and fits all AndyMark wheels. The bolt pattern is designated as 6 holes evenly spaced on a 1.875" diameter bolt circle. The hex broach is consistently cut to be aligned with the holes.

    Specifications:

    • Material: 6061 Aluminum
    • Bore: 0.376 - 0.380 hex bore (broached)
    • Bolt Pattern: 0.204" diameter holes, evenly spaced on a 1.875" diameter bolt circle
    • Outside diameter: 2.40"
    • Weight: 0.11 pounds

    This part is designed and fabricated in Indiana, USA.

    375 Key Hub

    #am-0134a
    $16,91
    (En stock)

    375 Key Hub. This hub fits all AndyMark wheels. These hubs now feature a 1.125" boss centering feature.

    Specifications:

    • Material: 6061 aluminum
    • Bore: 3/8" inside diameter, with a 3/32" keyway
    • Bolt Pattern: Six - 0.204" diameter holes, evenly spread on a 1.875" diameter bolt circle.
    • Finish: tumbled
    • Weight: 0.11 pound
    • Outside diameter: 2.25 inches

     

    NOTE: Some of these hubs feature an unneeded key way. These are not needed and will not hinder performance of the hub.

    5 mm Hex Double Boss Nub w/Set Screw

    #am-3670
    $18,45
    (En stock)

    The nub is a series of hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. It supports the output shaft of the AndyMark NeveRest motors as well as the other motors on the market. It supports the AndyMark 6mm D shafts for robust motion systems and impeccable torque transfer. The four mounting holes on these nubs are sized at 0.128" diameter, with the intention of accepting a #6-32 threaded screw. They are not tapped, but can be tapped by most machine screws due to this diameter.

    5 mm Hex Single Boss Nub w/ Set Screw

    #am-3669
    $15,38
    (En stock)

    The nub is a series of hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. It supports the output shaft of the AndyMark NeveRest motors as well as the other motors on the market. It supports the AndyMark 6mm D shafts for robust motion systems and impeccable torque transfer. The four mounting holes on these nubs are sized at 0.128" diameter, with the intention of accepting a #6-32 threaded screw. They are not tapped, but can be tapped by most machine screws due to this diameter.

    5 mm Hex XL Double Boss Nub w/Set Screw

    #am-3671
    $26,91
    (En stock)

    Nubs are hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. This Nub features a round boss on both sides with a 5 mm hex bore in the middle. This bore allows for pairing of REV 5mm hex components with other motion parts that interface with Nubs.

    The four mounting holes on these nubs are sized at 0.128" diameter, with the intention of accepting a #6-32 threaded screw. They are not tapped, but can be tapped by most machine screws once they are driven in the first time.

    Specifications:

    • Length: 0.630 in. (16 mm)
    • Height: 0.630 in. (16 mm)
    • Material: 6061-T6
    • Bore: 5 mm Hex
    • Overall Depth: 0.866 in. (22 mm)
    • Set Screw: Holes sized for 10-32 Set Screw (Set Screw Included)

    500 Key Hub

    #am-0077a
    $16,91
    (En stock)

    500 Key Hub. This hub fits all AndyMark wheels.

    The machine key is not included with this hub.

    Specifications:

    • Material: 6061 Aluminum
    • Bore: 0.501-505" diameter bore, with 1/8" keyway
      • 1/8x1/8x0400 Machine Key, steel (am-1018)
      • 1/8x1/8x0700 Machine Key, steel (am-1043)
    • Bolt Pattern: 0.204" diameter holes, evenly spaced on a 1.875" diameter bolt circle
    • Outside diameter: 2.25"
    • Weight: 0.1 pound

    500EX Key Hub

    #am-0976
    $15,38
    ( 10 En stock)

    This is the "500EX Key Hub". It is a slightly different version of the 500 Key Hub. It is manufactured differently, as it is extruded. Also, there is a 1.124" diameter boss on each side of the hub flange, providing a location for 1.125" bore flat sprockets. Are you having a hard time keeping your sprocket concentric with your hub? This hub is the trick.

    The bore is a 1/2" hole with two 1/8" keyways. Only one keyway is needed to drive most wheels, so the second one is extra.

    This hub fits all AndyMark wheels.

    Also, the keyways are consistently aligned with the mounting holes.

    Specifications:

    • Material: 6063 Aluminum
    • Bore: 0.502-508" diameter bore, with 1/8" keyway (2)
    • Bolt Pattern: 0.204" diameter holes, evenly spaced on a 1.875" diameter bolt circle
    • Outside diameter: 2.25"
    • Weight: 0.1 pound

    6 mm D-Bore XL Double Boss Nub w/Set Screw

    #am-3441a
    $13,84
    (En stock)

    The nub is a series of hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. It supports the output shaft of the AndyMark NeveRest motors as well as the other motors on the market. It supports the AndyMark 6mm D shafts for robust motion systems and impeccable torque transfer.

    6 mm Round Bore Double Boss Nub w/Set Screw

    #am-3413a
    $8,46
    (En stock)

    The nub is a series of hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. It supports the output shaft of the AndyMark NeveRest motors as well as the other motors on the market. It supports the AndyMark 6mm D shafts for robust motion systems and impeccable torque transfer.

    The four mounting holes on these nubs are sized at 0.128" diameter, with the intention of accepting a #6-32 threaded screw. They are not tapped, but can be tapped by most machine screws due to this diameter.

    Nub Specifications:

    • Length: 0.625"
    • Height: 0.625"
    • Material: 6105-T5 Aluminum
    • D-Bore: 6mm-D
    • Round Bore: 6mm
    • Single Boss Overall Depth: 10mm
    • Double Boss Overall Depth: 13mm
    • XL Double Boss Overall Depth: 22mm
    • Set Screw: Holes sized for 10-32 Set Screw (Set Screw Included)
    • Hole pattern: Four holes for 6-32 screws on a 16mm bolt circle

    6 mm Round Bore Single Boss Nub w/Set Screw

    #am-3442a
    $8,46
    (En stock)

    The nub is a series of hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. It supports the output shaft of the AndyMark NeveRest motors as well as the other motors on the market. It supports the AndyMark 6mm D shafts for robust motion systems and impeccable torque transfer. The four mounting holes on these nubs are sized at 0.128" diameter, with the intention of accepting a #6-32 threaded screw. They are not tapped, but can be tapped by most machine screws due to this diameter.

    6mm D-Bore Double Boss Nub w/Set Screw

    #am-3215a
    $8,46
    (En stock)

    Upgrades to Nubs:
    We are making improvements to the entire Nub line, including moving from the original machined design to one that is extruded and accepts screws more easily. Both kinds of Nubs will work fine, and you'll see the new-style Nubs (which you can identify by the open gaps between the screw holes and the edge of the Nub) as we exhaust supplies of the original Nubs.

    Product Overview:
    The nub is a series of hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. It supports the output shaft of the AndyMark NeveRest motors as well as the other motors on the market. It supports the AndyMark 6mm D shafts for robust motion systems and impeccable torque transfer.

    The four mounting holes on these nubs are sized at 0.128" diameter, with the intention of accepting a #6-32 threaded screw. They are not tapped, but can be tapped by most machine screws due to this diameter.

    Nub Specifications:

    • Length: 0.625"
    • Height: 0.625"
    • Material: 6105-T5 Aluminum
    • D-Bore: 6mm-D
    • Round Bore: 6mm
    • Single Boss Overall Depth: 10mm
    • Double Boss Overall Depth: 13mm
    • XL Double Boss Overall Depth: 22mm
    • Set Screw: Holes sized for 10-32 Set Screw (Set Screw Included)
    • Hole pattern: Four holes for 6-32 screws on a 16mm bolt circle

    6mm D-Bore Single Boss Nub w/Set Screw

    #am-3443a
    $8,46
    (En stock)

    Upgrades to Nubs:
    We are making improvements to the entire Nub line, including moving from the original machined design to one that is extruded and accepts screws more easily. Both kinds of Nubs will work fine, and you'll see the new-style Nubs (which you can identify by the open gaps between the screw holes and the edge of the Nub) as we exhaust supplies of the original Nubs.

    Product Overview:
    The nub is a series of hubs intended to connect motion components to spinning shafts, like sprockets gears, pulleys and wheels. It supports the output shaft of the AndyMark NeveRest motors as well as the other motors on the market. It supports the AndyMark 6mm D shafts for robust motion systems and impeccable torque transfer.

    The four mounting holes on these nubs are sized at 0.128" diameter, with the intention of accepting a #6-32 threaded screw. They are not tapped, but can be tapped by most machine screws due to this diameter.

    Nub Specifications:

    • Length: 0.625"
    • Height: 0.625"
    • Material: 6105-T5 Aluminum
    • D-Bore: 6mm-D
    • Round Bore: 6mm
    • Single Boss Overall Depth: 10mm
    • Double Boss Overall Depth: 13mm
    • XL Double Boss Overall Depth: 22mm
    • Set Screw: Holes sized for 10-32 Set Screw (Set Screw Included)
    • Hole pattern: Four holes for 6-32 screws on a 16mm bolt circle

    6mm Servo Hub 25T

    #76149
    $8,32
    ( 386 En stock)

    The 6mm Servo Hub 25T is made of anodized 6061-T6 Aluminum and is used to connect a servo motor to a D-Shaft axel.