M3 Nyloc Nut (100 pack)

Specifications:

• Diameter: M3
• Diameter - Thread Size: M3 - 0.5
• Drive: Hex
• Drive Size: 2.5mm
• Finish: Zinc
• Length: 5 mm
• Thread: Coarse
• Thread Size: 0.5
• Type: Socket Cap Screw

These gearboxes are designed with the same 37 mm diameter as the original 60:1 gearbox, while using the same 6 mm D-shaft and alignment pins, so getting the additional speed you need is a breeze.

M3 x 10mm Socket Head Cap Screw (pack of 100), Zinc Plated.

• Step File

The 60 Tooth GT2-6mm Timing Belt Pulley can be used with any of the GT2 belts. 

Specifications:

• 60 Tooth Timing Pulley
• 6mm Bore 
• Material: 6061 T6 Aluminum
• Step File

The Intake Kit can be used to create intake systems and is ideal for the FIRST Technical Challenge (FTC) and World Robotics Olympiad (WRO). Used with the Silicone Rubber Tubing #76410

Specifications:

• Main piece
  • hex width: 20.78mm*10.0mm thick
  • 6*M6 tapped holes
  • 1*M4 tappped hole for M4 set screw
  • 6.0mm Diameter D Hole
  • Material AL6061-T6
  • Φ7.5mm*14.0mm
• Pins
  • 6PCS in a pack
  • M6*4.0mm thread
  • Material SS303
• Step file

Φ29.0mm*16.0mm thick
6*M3 thread tapping through
(including 2*M3 thread for M3 SHCS)
Φ6.0mm D hole
AL6061-T6

M3 x 8mm Socket Head Cap Screw (pack of 100), Zinc Plated.

• Step File

M3 x 20mm Socket Head Cap Screw (pack of 50), Zinc Plated.

• Step File

M3 x 30mm Socket Head Cap Screw (pack of 50), Zinc Plated.

• Step File

The NeveRest 60 is a gearmotor with an attached encoder. The output shaft geometry and the gearbox housing diameter is similar to what FTC teams are familiar with. The shaft is 6mm dia and the gearbox housing is 37mm in diameter 

The power cable which feeds into the black encoder housing has two powerpole connectors already crimped to the end of the cable.

FTC Legality: 

According to the FIRST Tech Challenge Game Manual Part 1, Rule RE04 this is legal for the 2016-2017 FTC Game.

Encoder Cable options: 

Encoder cables are not included with this motor, and are sold separately. We have two options:

1. am-2992 is a cable which has the white 4-pin connector for the encoder and also the black 4-pin connector for the HiTechnic and Modern Robotics motor controller.
2. am-2993 is a cable which has the white 4-pin connector for the encoder on one end and 4 separate black connectors.

Encoder: 

There is an encoder mounted to the back side of this motor. It is a 7 pulse per revolution (ppr), hall effect encoder. Since the motor's gearbox has a 60:1 reduction, then the NeverRest 60 output shaft provides 420 ppr.

Working with the Encoders:

• https://ftc-tricks.com/dc-motors/
• https://www.reddit.com/r/FTC/comments/474wks/help_the_different_motor_modes_run_using_encoders/
• https://www.youtube.com/watch?v=d0liBxZCtrA

Specifications: 
Physical Specs:

• Overall Length: 133.5mm (5.26 in)
• Maximum Diameter: 37mm (1.46 in)
• Output Shaft size: 6mm (0.24 in) with 0.5mm deep flat
• Weight: 0.776 pounds
• Mounting Holes: M3 tapped holes, qty. 6, on a 31mm bolt circle (3.5mm depth MAX, beyond this can damage plate and stop motor)
• Electrical Connection Geometry: 6-pin connector for motor power and encoder contact
• Gear Material: Steel
• Body Material: Steel with plastic encoder housing
• Lubrication: Included with gearbox
• Shaft Hardness: 45-50 Rockwell C (https://en.wikipedia.org/wiki/Rockwell_scale)
• Wire Gauge: 18 AWG

Theoretical Performance Specs:

• Gearbox Reduction: 60:1
• Voltage: 12 volt DC
• No Load Free Speed, at gearbox output shaft: 105 RPM
• Gearbox Output Power: 14W
• Stall Torque: 593 oz-in
• Stall Current: 11.5A
• Output counts per revolution of Output Shaft (cpr): 1680 Pulses

Performance Specs, mounted to AndyMark dyno: Coming Soon

• Max Speed (under load of dyno):
• No Load Current (under load of dyno):
• Stall Current:
• Stall Torque:
• Max Output Power:
• Time to Failure at Stall:
• Motor Case Temperature at Failure: