Norgren relief valve

Pneumatic fitting with M5 threads and 1/4" push-in tubing port

This fitting screws into a CKD single or double solenoid valve. 

Specifications:

• Pisco fitting, part number POC1/4-M5
• Tubing diameter: 1/4 inch
• Mounting thread: M5
• Fastening method: Internal hex (use allen wrench)
• No pipe tape or additional sealant is needed for fastening these fittings
• Pressure rating: 150 psi

This is a push-to-connect "Y" fitting.

Specifications:

• Weight: 0.02 lbs
• Width: 1.515 in
• Height: 0.56 in
• Depth: 1.31 in
• Material: plastic body material
• Ports: 1/4" push-to-connect fitting
• Pressure range: 0-150 psi

This is a pneumatic push-to-connect union tee fitting. All three of the ports are push-to-connect 1/4" fittings.

Specifications:

• Weight: 0.02 pounds
• Width: 1.66"
• Height: 1.10"
• Depth: 0.525"
• Material: Plastic body
• Ports: 1/4" push-to-connect fitting
• Pressure range: 0-150 psi

This is an double solenoid, air-piloted, compact valve made by CKD. It's great for efficiently providing air to a small to medium sized actuator on mobile robots.

In order to make this work, you will also need three (3) M5 fittings (NOT INCLUDED) and some tubing (also NOT INCLUDED).

Link to CKD valve catalog

CKD part number: 4GA120R-M5-4

Specifications

• Cable Length: 3ft
• Flow Rate: 0.3 Cv
• Manufacturer: CKD
• Manufacturer Part #: 4GA120-M5-4
• Maximum Pressure: 125 psi
• Port(s): M5
• Voltage: 12Vdc
• Weight: 0.14 Lbs
• Width: 12mm

This is a blank cover fitting in where a valve would mount on the CKD manifold (am-3982). All 4 ports of the manifold are required to be covered by either a solenoid or by this cover.

Specifications

• Material: Plastic
• Maximum Pressure: 125 psi
• Style: Manifold-mounted
• Weight: 0.01 Lbs
• Width: 0.4 in.

These double acting single rod stainless steel cylinders are a solid choice when you want air actuated motion. These cylinders have a strong 0.75 in. thick bore and are available in multiple stroke lengths.

This is an single solenoid, air-piloted, compact valve made by CKD. It's great for efficiently providing air to a small to medium sized actuator on mobile robots.

In order to make this work, you will also need three (3) M5 fittings (NOT INCLUDED) and some tubing (also NOT INCLUDED).

Link to CKD valve catalog

CKD part number: 4GA110R-M5-4

Specifications

• Cable Length: 3ft
• Flow Rate: 0.3 Cv
• Manufacturer: CKD
• Manufacturer Part #: 4GA110-M5-4
• Maximum Pressure: 125 psi
• Port(s): M5
• Voltage: 12Vdc
• Weight: 0.1 Lbs
• Width: 12mm

This is a hex nipple brass fitting, with one end being 1/4" NPT and the other being 1/8" NPT port. The intent of this part is to connect the air compressor (pump) to the aluminum manifold within the Pneumatics Base Kit.

Specifications:

• Weight: 0.05 pound
• Length: 1.15 inch
• Hex Width: 9/16 inch
• Material: Brass
• Ports: 1/4" NPT and 1/8" NPT
• Pressure range: 0-250 psi

This is an air pressure switch with a factory preset setting of 115-120 psi. This switch is able to send a signal to a robot controller, which can then tell a pneumatic compressor (air pump) to stop operating.

Specifications

• Circuit: SPST-NC
• Current Rating: 5 amps @ 30 VDC
• Cycle Life: 1 million
• Fixed set point: 115 psi
• Manufacturer: Nason
• Manufacturer Part #: SM-2B-115R/443
• Maximum Operating Pressure: 250 psi
• NEMA Rating: NEMA 4, 13
• Port(s): 1/8 in. NPT Male
• Screw Terminals: #8-32
• Set Point Direction: Rising

Documents

Guide(s)

am-2006 Data Sheet.pdf

VIAIR 90C compressor (air pump) offers a light duty solution for smaller air requirements. These compact compressors and are meant to fill no larger than a 1.0 gallon air tank. 

VIAIR part number 00090

Specifications:

• Manufacturer: VIAIR Corporation
• Weight: 2.4 pounds
• Width: 2.11 inches
• Height: 4.53 inches
• Length: 5.94 inches
• Material: Steel and aluminum
• Manufacturer: Viair Corporation
• Part Number: 00090
• Flow Rate: 0.88 cfm at 0 ps
• Ports: 1/8" NPT
• Voltage: 12 Volt DC
• Permanent Magnet Motor
• Duty Cycle: 9% @ 100 psi
• Maximum Working Pressure: 120 psi
• Maximum Amp Draw: 11 amps

Hardware: 

• Vibration Isolators (4)
• Screw (4)
• Nut (4)
• Washer (8)
• Lock Washer (4)

Fill Rate

• This pump will take approximately 13 seconds to fill one (1) plastic Clippard tank (574 ml) from 0 to 120 psi.

Products to be used on:

• Mobile Robots
• Outdoor equipment

For VIAIR compressor warranty replacements contact Ryan Shaw.

• Phone: 949-585-0011 x110
• Email: [email protected]