Hex Nipple, 1/4"-1/8" NPT

Pneumatic fitting with M5 threads and 1/4" push-in tubing port

This fitting screws into a CKD single or double solenoid valve. 

Specifications:

• Pisco fitting, part number POC1/4-M5
• Tubing diameter: 1/4 inch
• Mounting thread: M5
• Fastening method: Internal hex (use allen wrench)
• No pipe tape or additional sealant is needed for fastening these fittings
• Pressure rating: 150 psi

This is a heavy-duty compression lug from BURNDY for 06 AWG wire. This compression log can be easily crimped with the Cable Lug Crimping Tool.

Specifications

• Gauge: 06 AWG
• Hole Size For Stud: 0.25 in.
• Material: Copper
• Overall Length: 2.03 in.
• Tongue Width: 0.48 in.
• Weight: 0.01 lbs
• Wire Strip Length: 1.18 in.

This is a pneumatic push-to-connect union tee fitting. All three of the ports are push-to-connect 1/4" fittings.

Specifications:

• Weight: 0.02 pounds
• Width: 1.66"
• Height: 1.10"
• Depth: 0.525"
• Material: Plastic body
• Ports: 1/4" push-to-connect fitting
• Pressure range: 0-150 psi

This is a push-to-connect "Y" fitting.

Specifications:

• Weight: 0.02 lbs
• Width: 1.515 in
• Height: 0.56 in
• Depth: 1.31 in
• Material: plastic body material
• Ports: 1/4" push-to-connect fitting
• Pressure range: 0-150 psi

This novel style of collar clamp is split into two pieces so that it can be attached without removing any shafts. The bore is a 1/2" hex. The flats on the perimeter allow for the collar clamp to be held in position or turned for better assembly control. 

This clamp has been designed and fabricated by BaneBots, and proudly sold through AndyMark.

Specifications:

• Material: Aluminum
• Bore: hex hole, 1/2 inch
• Outside Diameter: 0.94 inch
• Thickness: 0.375 inch
• Width Across Flats: 7/8 inch
• Weight: 0.020 pound
• Clamping Screws: #6-32 x 1/2" long (qty. 2)

Plastic spacers are included with this clamp, positioned between the two halves. These are to be removed before usage.

Tip-to-tip length is approximately 12.6 inches.

This is an single solenoid, air-piloted, compact valve made by CKD. It's great for efficiently providing air to a small to medium sized actuator on mobile robots.

In order to make this work, you will also need three (3) M5 fittings (NOT INCLUDED) and some tubing (also NOT INCLUDED).

Link to CKD valve catalog

CKD part number: 4GA110R-M5-4

Specifications

• Cable Length: 3ft
• Flow Rate: 0.3 Cv
• Manufacturer: CKD
• Manufacturer Part #: 4GA110-M5-4
• Maximum Pressure: 125 psi
• Port(s): M5
• Voltage: 12Vdc
• Weight: 0.1 Lbs
• Width: 12mm

This Inline Chain Tensioner for #35 series roller chain is perfect to adjust the desired tension in a long run of chain on mechanisms such as elevators and arms. This is ideal where there is at least a ~3" section of chain that never passes over a sprocket in a given mechanism. Pair this with two #35 Master Links and integrate this to your robot for an easy-to-use chain tension solution!

The design of this product was inspired by Misumi's Chain Turnbuckles. This product has been improved to be compatible with imperial-sized wrenches.

Specifications

• Chain Size: #35

Documents

CAD File(s)

am-3914_35 35 Chain Tensioner.STEP

Layout Print(s)

am-3914_35 #35 Chain Inline Tensioner.PDF

This is a pneumatic meter-out flow control valve. The port is a 1/8" NPT male thread, and 1/4" diameter tube can be pressed in to the push-to-connect fitting.
 

Meter-out allows for the flow to be controlled in one direction, while the opposite flow is not restricted.

Specifications

• Hex Width: 7/16 in.
• Material: Rotating thermoplastic (PBT) body, nickel-plated brass threads, stainless steel tube griping claws, and pre-applied Teflon thread sealant
• Port(s): 1/8 in. NPT male with pre-applied Teflon thread sealant
• Weight: 0.01 lbs

Sauro CTF020V8 connector, to be used as the power connector with  the roboRIO