Fermer
toutes catégories
    filtres
    préférences
    Rechercher

    Smart Servos

    Smart Servos

    Voir comme Grille Lister
    Trier par
    Affichage par page

    6V DC Battery Holder, for Smart Robotics Servo Programmer

    #75004
    $6.88
    (4374 En stock)

    Use it to power the Studica Smart Robot Servo Programmer or any other device requiring 6V output and a TJC8 connector. 

    Specifications:

    • 6V Output
    • On/Off Power switch
    • TJC8 connector
    • Uses 4 x 1.5V AA Batteries (not included)

    Fast Multi-Mode Smart Servo

    #75007
    Demander un devis

    The Studica Fast Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Fast Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

     

    Multi-Mode Smart Servo

    #75002
    $33.07
    (2257 En stock)

    The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

    Specifications:

    Type:                             Metal Brush Motor
    Horn Gear Spline:       25T (5.9mm)
    Size:                               40mm x 20.1mm x 38.3mm
    Weight:                          65g
    Maximum Speed:        62RPM at 6V
    Stall Torque:                 20kg.cm at 6V
    Voltage:                         6-7 4V
    Cable:                             22AWG, 75cm

    Servo Pack

    #70254
    $467.33
    (0 En stock)

    Includes,

    • 8 - Multi-Mode Smart Servo  75002
    • 1 - Smart Robot Servo Programmer  75003
    • 1 - 6V DC AA Battery Holder w/TJC8 Female, 22 AWG  75004
    • 1 - Servo Power Block  75006
    • 4 - Servo Standard Front Mount  76144
    • 4 - Servo Mount Flat Plate  76145
    • 4 - Servo Mount Offset Plate  76146
    • 8 - Servo Horn 25T  76148
    • 8 - 6mm D-Shaft Servo Hub 25T  76149

    Servo Power Block

    #75006
    $50.99
    (2043 En stock)

    The Studica Servo Power Module is a 6V, 60W power injector that enables the use of high-power RC servos. The Servo Power Module passes through input signals unaltered while providing up to 60W of total output power across all eight channels.  The input and output channels accept standard 3-wire, 0.1” pitch, servo/PWM cables. 

    Features,

    • Built in DC-DC converter
    • Over-current shutdown
    • ESD protection

    Specifications,

    • Nominal Input Voltage: 12V
    • Operational Voltage Range: 6.0V
    • Number of Channels: 8
    • Max Current for All Channels Combined: 10A
    • Total Continuous Power: 60W
    • Size: 70mm x 45mm x 16mm
    • Step File

     

    Smart Robot Servo Programmer

    #75003
    $17.91
    (733 En stock)

    The Studica Smart Robot Servo Programmer is used for programming the Studica Multi-Model Smart Servo Motor and for testing other standard Servos. Use it to program the Studica Servo to switch between continuous mode, standard mode, or any custom angular mode.  

    Specifications:

    • Requires 6 Volt battery pack with TJC8 connector or use the Studica 6V DC Battery Holder.
    • Programming setting modes
      • Standard
      • Continuous
      • Angular