Specifications:

• Material: 6061-T6 Aluminum
• Thickness: 12mm
• Step File

The Studica Linear Servo RC Actuator 50S-40N is a new Servo motor which has a stroke of 50mm, Max Force load of 50N and stroke spead of 26mm/s. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

Includes,

• 4 - 100mm Drive Wheel, 50A, 12.5mm wide, 1/2" Inner Hex, Blue  76261
• 4 - 100mm Drive Wheel, 50A, 25mm wide, 1/2" Inner Hex, Blue  76262
• 4 - 50mm Drive Wheel, 50A, 25mm wide, 1/2" Inner Hex, Blue  76269
• 4 - 100mm Omni Wheel  76272
• 2 - 6mm x 96mm D-Shaft (6 pack)  76161-6
• 1 - 6mm x 432mm D-Shaft (2 pack)  76162-2
• 1 - Bushing Bronze 6mm ID x 8mm OD (12 Pack)  76300-12
• 1 - Bushing Bronze 6mm ID x 14mm OD (12 Pack)  76301-12
• 1 - Flange Bearing  6mm ID, 14mm OD, 15mm Flange (12 Pack)  76302-12
• 3 - 6mm Shaft Hub (4 pack)  76284-4
• 2 - Collar 6mm ID D-Shaft, 12mm OD (6 pack)  76304-6
• 1 - Shaft Spacer Plastic 6mm ID x 10mm OD x 1mm L (24 pack)  76305-24

Our improved and  stronger 12-volt DC motor with 100 rpm and 708 oz-in. of torque. The motor features a built-in, high-resolution Hall effect encoder for precise motor control and comes with an encoder cable.

A 61:1 gearbox comes standard.

Output Counts per Revolution of Output Shaft (cpr) 1,464 pulses

This motor is FTC Competition Legal

Includes,

• 2 - 13 Tooth Bevel Gear (2 pack)  76223-2
• 2 - 26 Tooth Bevel Gear (2 pack)  76224-2
• 4 - 30 Tooth Bevel Gear (2 pack)  76219-2
• 2 - Rack & Pinion  76170
• 2 - 6mm Shaft Hub (4 pack)  76284-4
• 1 - M3 x 12mm Socket Head Cap Screw (pack of 100)  76202-100

The Servo Mount Flat Plate is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.

• Step File

The Servo Mount Offset Plate is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.

• Step File

The Servo Power Block is a 6V, 60W power injector that provides proper power for RC Servos. It does not interfere with the signal, it will only replace the power to the servo with 6V. 

Features,

• Built in DC-DC converter
• Over-current shutdown
• ESD protection

Specifications,

• Nominal Input Voltage: 12V
• Operational Voltage Range: 6.0V
• Number of Channels: 8
• Max Current for All Channels Combined: 10A
• Total Continuous Power: 60W
• Size: 70mm x 45mm x 16mm
• Step File

The Servo Standard Front Mounting Bracket is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.

• Step File

Can be used with 6mm D-Shaft Axel and 6mm shaft DC motor. 

Specifcations:

• Material: 6061-T6 Aluminum
• Inside Diameter: 6mm
• Outside Diameter: 12mm
• Step File

The Studica Smart Robot Servo Programmer is used for programming the Studica Multi-Model Smart Servo Motor and for testing other standard Servos. Use it to program the Studica Servo to switch between continuous mode, standard mode, or any custom angular mode.  

Specifications:

• Requires 6 Volt battery pack with TJC8 connector or use the Studica 6V DC Battery Holder.
• Programming setting modes
  • Standard
  • Continuous
  • Angular

Using the Smart Servo Programmer

The XL series belt is compatible with the 6mm, 10 tooth XL pulley.

Specifications:

• Material: Neoprene with Fiberglass cords
• Length: 1 meter
• Width: 9mm

Specifications:

• Size: 1/10 standard car
• Material: Aluminum alloy
• Total length: 63mm
• Ball head to ball head: 55mm
• Diameter: 17mm 
• Ball head hole diameter: 3mm  
• Step File - Shock in compressed mode
• Step File - Shock in extended mode

Specifications:

• Size: 1/10 standard car
• Material: Aluminum alloy
• Total length: 108mm
• Ball head to ball head: 100mm
• Diameter: 17mm 
• Ball head hole diameter: 3mm 
• Step File - Shock in compressed mode
• Step File - Shock in extended mode

The 5mm Round Groove Belt is 3M long and has a 10% stretch. It is also referred to as a U Groove belt. 

• Material - Polyurethane
• Diameter - 5mm
• Length - 3m
• Color - Yellow
• Stretch factor - 10%
• Surface - smooth
• Solid core
• Open end

The pulleys are .40” inside the flanges to allow for belts up to 3/8” in width. Two set screws using 1.5mm hex key.

3/8” wide, 1/5 pitch XL series belti. Constructed of Neoprene with Fiberglass cords for superior strength and wear resistance. Compatible XL series pinion pulley.

Includes two 5mm Bore, 10 Tooth Aluminum Pulleys and one 1M XL Timing belt

Replacement Hub for Studica Omni or Mecanum wheels so they can be used on 5mm Hex-Shafts.

Step File

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 140mm length
• 6mm OD
• 5.5mm to flat
• Step File

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 10mm
• Step File

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 20mm
• Step File

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 30mm
• Step File

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 40mm
• Step File

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 50mm
• Step File

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 60mm
• Step File

The 100mm Drive Wheel (4") can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.

Use with 1/2" hex shaft of use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.

Specifications:

• Diameter:   100mm (4")
• Axial width:  12.5mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Blue
• Outer Material Durometer: 50A
• Weight: 0.068kg
• Step File

The 100mm (4") Flex Wheel can be used for intake systems and conveyors.

Specifications:

• Diameter:   100mm (4")
• Axial width:  25mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Green
• Outer Material Durometer: 35A
• Weight: 0.038kg
• Step File

The 100mm (4") Flex Wheel can be used for intake systems and conveyors.

Specifications:

• Diameter:   100mm (4")
• Axial width:  25mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Orange
• Outer Material Durometer: 40A
• Weight: 0.038kg
• Step File

The 100mm (4") Flex Wheel can be used for intake systems and conveyors.

Specifications:

• Diameter:   100mm (4")
• Axial width:  25mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Blue
• Outer Material Durometer: 50A
• Weight: 0.038kg
• Step File

The 100mm (4") Flex Wheel can be used for intake systems and conveyors.

Specifications:

• Diameter:   100mm (4")
• Axial width:  25mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Black
• Outer Material Durometer: 60A
• Weight: 0.038kg
• Step File

The 50mm (2") Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.

Use with 1/2" hex shaft of use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.

Specifications:

• Diameter:   40mm (2")
• Axial width:  25mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Orange
• Outer Material Durometer: 40A
• Weight: 0.038kg
• Step File

The 50mm (2") Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.

Use with 1/2" hex shaft of use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.

Specifications:

• Diameter:   50mm (2")
• Axial width:  25mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Blue
• Outer Material Durometer: 50A
• Weight: 0.038kg
• Step File

The 50mm (2") Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.

Use with 1/2" hex shaft of use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.

Specifications:

• Diameter:   50mm (2")
• Axial width:  25mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Black
• Outer Material Durometer: 60A
• Weight: 0.038kg
• Step File

The 75mm Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.

Use with 1/2" hex shaft of use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.

Specifications:

• Diameter:   75mm
• Axial width:  12.5mm 
• Hub:  1/2" Inner Hex
• Inner Material: Molded Plastic in Yellow
• Outer Material: TPU Polyurethane in Black
• Outer Material Durometer: 60A
• Weight: 0.05kg
• Step File

The 20 Tooth GT2-6mm Timing Belt Pulley can be used with any of the GT2 belts. 

Specifications:

• 20 Tooth Timing Pulley
• 6mm Bore 
• Material: 6061 T6 Aluminum
• Step File

The 40 Tooth GT2-6mm Timing Belt Pulley can be used with any of the GT2 belts. 

Specifications:

• 40 Tooth Timing Pulley
• 6mm Bore 
• Material: 6061 T6 Aluminum
• Step File

The 60 Tooth GT2-6mm Timing Belt Pulley can be used with any of the GT2 belts. 

Specifications:

• 60 Tooth Timing Pulley
• 6mm Bore 
• Material: 6061 T6 Aluminum
• Step File

The 80 Tooth GT2-6mm Timing Belt Pulley can be used with any of the GT2 belts. 

Specifications:

• 80 Tooth Timing Pulley
• 6mm Bore 
• Material: 6061 T6 Aluminum
• Step File

GT2-6mm Smooth Idler Pulley, H Type, w/3mm Inner Bore Bearing

The GT2-6mm Timing Belt Clamp w/Set Screw is used with all the GT2 belts. 

Specifications:

• Step file

This GT2 (also called 2GT) timing belt has a 2mm Pitch and 6mm width

Specifications:

• type: GT2 closed-loop 108mm 
• pitch: 2 mm
• width: 6 mm
• material: neoprene rubber, fiberglass reinforced
• belt shape: circular tooth profile

This GT2 (also called 2GT) timing belt has a 2mm Pitch and 6mm width

Specifications:

• type: GT2 closed-loop 140mm 
• pitch: 2 mm
• width: 6 mm
• material: neoprene rubber, fiberglass reinforced
• belt shape: circular tooth profile

This GT2 (also called 2GT) timing belt has a 2mm Pitch and 6mm width

Specifications:

• type: GT2 closed-loop 190mm 
• pitch: 2 mm
• width: 6 mm
• material: neoprene rubber, fiberglass reinforced
• belt shape: circular tooth profile

This GT2 (also called 2GT) timing belt has a 2mm Pitch and 6mm width

Specifications:

• type: GT2 closed-loop 240mm 
• pitch: 2 mm
• width: 6 mm
• material: neoprene rubber, fiberglass reinforced
• belt shape: circular tooth profile

This GT2 (also called 2GT) timing belt has a 2mm Pitch and 6mm width

Specifications:

• type: GT2 closed-loop 330mm 
• pitch: 2 mm
• width: 6 mm
• material: neoprene rubber, fiberglass reinforced
• belt shape: circular tooth profile

This GT2 (also called 2GT) timing belt has a 2mm Pitch and 6mm width

Specifications:

• type: GT2 closed-loop 630mm 
• pitch: 2 mm
• width: 6 mm
• material: neoprene rubber, fiberglass reinforced
• belt shape: circular tooth profile