The easy way to change the length of your #25 chain. (Chain not included)

This kit is a tried and tested addition to the Climber in a Box. It is used as a secondary bracing point between the outermost piece of extrusion and the robot that the Climber is attached to. It also has mounting holes to accept our Peanut Extrusion, which can be used to brace two Climber arms together across a robot.

Items Included in am-4682:

• 2 - Cross Support Plate (am-4655) 
• 5 - 0.192 in. ID 0.375 in. OD 1.5 in. Long Aluminum Spacer (am-1599)
• 5 - 10-32 x 2 in. Socket Head Cap Screw (am-1049)
• 5 - 10-32 Nylock Jam Nut (am-1063)

Items Included in am-4683:

• 2 - Cross Support Plate (am-4655) 
• 5 - 0.192 in. ID 0.375 in. OD 2 in. Long Aluminum Spacer (am-1600)
• 5 - 10-32 x 2.5 in. Socket Head Cap Screw (am-1024)
• 5 - 10-32 Nylock Jam Nut (am-1063)

The Cobra Line Follower Array provides 4 X QRE1113 IR reflectance sensor mounted on a 9mm pitch Each sensor is comprised of two parts - an IR emitting LED and an IR sensitive phototransistor. When you apply power to the VCC and GND pins the IR LED inside the sensor will illuminate.

The Studica Line Sensor Board consists of 4 IR LED/phototransistor pairs, making it a great detector for a line-following robot.  The Line Sensor Board allows the robot to tell objects or surfaces apart based on how dark or light they are. It shines a beam of infrared light out onto the object, and measures how much light is reflected back.

Each sensor provides a separate analog voltage output. The sensor board is an infrared emitter/receiver that is able to differentiate between a dark surface (with low IR reflectivity – 3.3V to 5V) and a light surface (with high IR reflectivity – 0V to 0.5V). However, this range can vary depended on the installed height of the sensor board. 

The optimum height distance is 3-5 mm; however, the reflectivity values will change depending on distance. A daylight filter is built into the sensor.

• 5VDC operating voltage (recommended)
• 70mA supply current
• Optimal sensing distance: 0.125" (3mm)
• Step File

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 140mm length
• 6mm OD
• 5.5mm to flat
• Step File

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 35mm length
• 6mm OD
• 5.5mm to flat
• Step File

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 432mm length
• 6mm OD
• 5.5mm to flat
• Step File

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 70mm length
• 6mm OD
• 5.5mm to flat
• Step File

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 96mm length
• 6mm OD
• 5.5mm to flat
• Step File

Ideal for the myRIO.

• Inside Contact Diameter: 2.1mm
• Outside Contact Diameter: 5.5mm
• Termination Style: Solder Cup
• Voltage Rating: 12 V
• 6 Amp
• 1 meter cord length
• 18AWG or 20AWG wire guage
• DC connector type

• Inside Contact Diameter: 2.1mm
• Outside Contact Diameter: 5.5mm
• Termination Style: Solder Cup
• Voltage Rating: 12 V
• 6 Amp
• 1 meter cord length
• 18AWG wire guage
• DC connector type

49mm x 87mm sign used with 127mm high sign holder.

The D-Shaft Collar is 6mm ID and 12mm OD. The inside diameter will fit any of the D-Shaft axels.

Specifcations:

• Material: 6061-T6 Aluminum

• Step File

Use the Dupont Single Pin - 4 wire - female to female cable with the Ultrasonic Distance Sensor

Specifications: 

• Dupont Single Pin
• 4 wire
• female to female cable
• Length: 50cm
• Gauge: 22AWG

The Studica End Piece Plate is commonly fastened to the inside end of the U Channel. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.

Specifications:

• Material: 6061-T6 Aluminum
• Step File

Includes,

• 2 - 336mm U-Channel  76012
• 1 - 288mm U-Channel (2 pack)  76013-2
• 2 - 144mm U-Channel (2 pack) 76016-2
• 2 - 96mm U-Channel (2 pack)  76017-2
• 2 - 48mm U-Channel (2 pack)  76018-2
• 2 - 336mm x 40mm Flat Bracket  76060
• 1 - 288mm x 40mm Flat Bracket (2 pack)  76061-2
• 1- 192mm x 40mm Flat Bracket  76063-2
• 1 - 144mm x 40mm Flat Bracket  76064-2
• 1 - 96mm x 40mm Flat Bracket  76065-2
• 1 - 192mm x 96mm Flat Bracket (2 pack)  76066-2
• 3 - L Bracket (2 pack)  76087-2
• 3 - Inside L Bracket (2 pack)  76089-2
• 1 - 6mm x 96mm D-Shaft (6 pack)  76161-6
• 2 - Collar 6mm ID D-Shaft, 12mm OD (6 pack)  76304-6
• 1 - Bushing Bronze 6mm ID x 8mm OD (12 Pack) 76300-12
• 1 - Bushing Bronze 6mm ID x 14mm OD (12 Pack) 76301-12
• 1 - Flange Bearing  6mm ID, 14mm OD, 15mm Flange (12 Pack) 76302
• 1 - Shaft Spacer Plastic 6mm ID x 10mm OD x 1mm L (24 pack)  76305-24
• 1 - Shaft Spacer Plastic 6mm ID x 10mm OD x 2mm L (24 pack)  76306-24
• 2 - 6mm Shaft Hub (4 pack)  76284-4
• 2 - 32 Tooth Gear (2 pack)  76220-2
• 1 - 64 Tooth Gear (2 pack)  76221-2
• 2 - 128 Tooth Gear  76222
• 1 - Rack & Pinion (2 pack)  76170-1
• 1 - Multi-Mode Smart Servo  75002
• 1 - M3 x 8mm Socket Head Cap Screw (pack of 100)  76200-100
• 1 - M3 x 10mm Socket Head Cap Screw (pack of 100)  76201-100
• 1 - M3 x 12mm Socket Head Cap Screw (pack of 100)  76202-100
• 1 - M3 x 10mm Button Head Cap Screw (pack of 50)  76203-50
• 1 - M3 Kep Nut (pack of 100)  76204-100
• 1 - 25mm Standoff (12 pack)  76182-12
• 1 - 48mm Standoff (12 pack)  76181-12