This gear comes standard as the pinion for the NeveRest motor, am-3104 

Specifications:

• Module: 0.5
• Tooth Count: 12
• Pressure Angle: 20 Degrees
• Helix Angle: 18 Degrees, Left
• Bore: 2.98mm

Overview:
This 35 Tooth Dog Gear features a bearing bore suited to press fit a 1.125" diameter bearing, allowing this gear to serve as an output gear on a 0.500" shaft, as featured in our Rocketbox PTO.

Specifications:

• Material: 4140 Steel
• Diametral pitch: 20
• Pressure angle: 14.5
• Number of teeth: 35
• Pitch Diameter: 1.75 inch
• Bore: 1.1249" - 1.1241"
• Thickness: 0.425"
• Weight: 0.154

Sheet Aluminum Plate for back side of the Work Gearbox.

Specifications:

• Width: 3.625" (4.563" at tabs)
• Height: 4.75"
• Depth: 1.463" at L
• Material: 6061 Aluminum (.0875" thick)
• Weight: 0.16 Lb

Specifications:

• Bore: 0.375 in. Hex
• Series: #25
• Weight: 0.034 Pounds
• Material: 7075-T6 Aluminum
• Thickness: 0.1 in.
• Tooth Count: 18
• Hub Diameter: 0.873 in.
• Overall Depth: 0.4 in.
• Pitch Diameter: 1.440 in.
• Outside Diameter: 1.568 in.

This gear is used as the input pinion gear for the EVO Shifter. This gear is a tight press fit onto a CIM gear, and requires at minimum a 3-ton arbor press to install. If a CIM motor with this gear pre-installed interests you, check out am-0255_15T. 

Specifications:

• Tooth Count: 15
• Diametral Pitch: 32
• Pressure Angle: 20
• Pitch Diameter: 0.469"
• Face Width: 0.531"
• Thickness: 0.75"
• Material: 1117 Steel
• Bore: 0.312" Round (7.92mm) This is a press fit onto the CIM Motor (am-0255)
• Weight: 0.019 Lbs

Specifications:

• Bore: 0.375 in. Hex
• Series: #25
• Weight: 0.06
• Material: 7075-T6 Aluminum
• Thickness: 0.1 in.
• Tooth Count: 24
• Hub Diameter: 1.123 in.
• Overall Depth: 0.4 in.
• Pitch Diameter: 1.91 in.
• Outside Diameter: 2.049 in.

Specifications:

• Tooth Count: 14
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 0.7
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex
• Weight: 0.029 Lbs

End Plate for the Worm Gearbox.

Specifications:

• Weight: 0.08 pounds
• Width: 1.28"
• Height: 4.57"
• Depth: 0.25"
• Material: Clear Polycarbonite

This is a 18 tooth sprocket with a 10mm DD bore.

Specifications:

• Tooth Count: 24
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.2"
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex
• Weight: 0.1 Lbs

This is a 24 tooth sprocket with a 10mm DD bore.

Specifications:

• Tooth Count: 35
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.75"
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.5" Hex
• Weight: 0.146 Lbs

This is the plate on the TB3 Gearbox that is on the motor side.
Specifications:

• Material: 6061 Aluminum
• Size: 5" x 5" x 1/4"
• Weight: lbs