The Plate spacer goes on the opposite side of the RAW box from the CIM Motor. 

Specifications:

• Material: 6061 Aluminum
• Length: 3.5"
• Height: 1"
• Thickness: 0.312"
• Weight: 0.07 Pounds

This is the aluminum shaft plate for our 3 Motor Toughbox. A standard Toughbox could be converted to a 3 Motor Toughbox by using this plate and also the 3 Motor Toughbox Motor Plate.

Specifications:

• Size: 5x5x0.125 inches
• Material: 6061 Aluminum
• Weight: 0.274 pound
• Finish: Tumbled

Specifications:

• Tooth Count: 34
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.7"
• Face Width: 0.375":
• Material: 4140 Steel
• Bore: 0.375" Hex

This is the aluminum motor mount plate for our 3 Motor Toughbox. A standard Toughbox could be converted to a 3 Motor Toughbox by using this plate and also the 3 Motor Toughbox Shaft Plate.

Specifications:

• Size: 5x5x0.25 inches
• Material: 6061 Aluminum
• Weight: 0.528 pound
• Finish: Tumbled

Specifications:

• Tooth Count: 38
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.9"
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex

Specifications:

• Tooth Count: 36
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 1.8"
• Face Width: 0.438"
• Material: 4140 Steel
• Dog Profile: 4 Tooth, 90 Degrees Opposed
• Bearing Bore: 1.124"

This 1/8" thick plate supports the output shaft of the SpinBox gearbox. This plate has the same outer size as the SpinBox Housing.

Specifications:

• Tooth Count: 46
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 2.25
• Face Width: 0.438"
• Material: 4140 Steel
• Dog Profile: 4 Tooth, 90 Degrees Opposed
• Bearing Bore: 1.124"
• Weight: 0.24 Lbs

This 1/8" thick plate supports the output shaft of the SpinBox gearbox. This plate has the same outer size as the SpinBox Housing.

Specifications:

• Tooth Count: 52
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 2.6"
• Face Width: 0.438"
• Material: 4140 Steel
• Dog Profile: 4 Tooth, 90 Degrees Opposed
• Bearing Bore: 1.124"
• Weight: 0.3 Lbs

This is the plate on the Sonic Shifter that is on the motor side. This plate has two 1/4-20 steel threaded inserts pressed in to one end of the plate.

The dog gear has 4 dogs on each face. This allows more material around the dog gear screw, increasing strength over previous designs. A robust 1/8" diameter shoulder screw replaces the previously used #4-40 screw. The dog gear material is AMPCO® 18 Bronze. This material has similar properties to stainless steel (previously used), but has added lubricity for smooth shifting.

This conversion plate acts as a hub between larger motion components featuring a 1.875" bolt circle to components of a smaller mounting circle such as a NeveRest Gearmotor. The bore of this plate fits shafts that are familiar to FIRST Tech Challenge teams.

Specifications:

• Material: 5052 Aluminum
• Bore: 0.320" (8.1mm)
• Outside Bolt Pattern: 0.204" diameter holes on a 1.875" diameter circle
• Inside Bolt Patterns:
• Four - 0.150" (3.8mm) diameter holes on a 0.630" (16mm) diameter circle
• Four - 0.160" (4mm) diameter holes on a 0.770" (19.5mm) diameter circle
• Outside Diameter: 2.125" from side to side
• Thickness: 0.125"
• Material: 5052 Aluminum

This 12 tooth pinion gear is designed to fit onto an AndyMark RedLine Motor (am-3775) and other motors with a 5 mm output shaft to interface with spur gearboxes such as the DeCIMate (am-3745), EVO Slim for RedLine and EVO Shifter for RedLine. 

Specifications:

• Bore: 5mm press fit
• Weight: 0.014 Pounds
• Material: 1117 Steel
• Overall Length: 0.755 in.
• Face Width: 0.625 in.
• Tooth Count: 12
• Pitch Diameter: 0.375 in.
• Pressure Angle: 20
• Diametral Pitch: 32

The Plate used in the PVC Arm Joint

Specifications

• Height: 3.505"
• Length: 5"
• Material: 6061 Aluminum
• Thickness: 0.188"
• Weight: 0.22 lbs

Specifications:

• Tooth Count: 45
• Diametral Pitch: 32
• Pressure Angle: 20
• Pitch Diameter: 1.406"
• Material: 4140 Steel
• Bore: 0.375 in. Hex
• Weight: 0.115 Pounds