This is an 11 tooth steel gear. This gear fits onto the 9015 motor shaft so that the 9015 motor can mate with the PG27 gearbox. 

Specifications:

• Number of teeth: 11
• Module: 0.6
• Pitch Diameter: 6.6 mm
• Pressure Angle: 20
• Bore 3.17mm (0.125 inch)
• Overall Thickness: 8mm
• Overall Diameter: 0.406"
• Weight: 0.001 lbs
• Material: 1215 Steel

This cable can be used in many ways, a power cable for the Gorgon Flex, or from a Speed Controller to a CIM motor. One end connectors are crimped with PowerPole Connectors, two crimps and a black and red housing are shipped with this cable. Tip-to-tip length is approximately 24 inches. 

Specifications:

• Weight: pounds
• Length: Approximately 24 inches
• Connector Type: Anderson PowerPole PP45
• Gauge: 12 bonded

This is 12 GA bonded wire* with Red and Black Jacketing. It is much easier to use than two separate wires, easier to follow during troubleshooting, and easier to keep your wiring clean. Pull apart at the end only as much as you need and the rest stays together.

If you are looking for a much more flexible wire or wire that is not bonded check out our Silicone Wire. 
 

* - This is also known as zip cord or zip wire.

Specifications

• Gauge: 12 AWG
• Length: 25 feet
• Total Weight: 1.2 lbs
• Weight: 0.05 lbs/ft
• Wire Jacketing: black & red (bonded together)

This 120 Amp Circuit breaker forms the main circuit breaker for FIRST Robotics Competition robots. It can protect your robot or other system from drawing so much current that systems receive more damage. Of course, we highly recommend using circuit breakers downstream rated for less to protect your motors, speed controllers, and control system components.

Specifications:

• Weight: 0.24 pounds
• Size: 2.9 x 1.9 x 1.5 inches
• Surface Mount Style
• Terminal Supply part number: CB3-SM-120
• Type III Breaker Manual Reset

The 120 Degree Bracket is perfect for connecting two channel pieces at 120 degrees from each other. Each side is 48mm wide to fit perfectly on the channel. Use three brackets with 3 channel pieces to make 3 wheeled robots. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.

Specifications:

• Material - Anodized 6061-T6 Aluminum
• Thickness - 3mm
• Step File

Specifications:

• Material: 6061-T6 Aluminum
• Thickness: 6.35mm
• Hole Diameter: 14mm
• Number of teeth: 128
• Step File

Servo City's patented 32 pitch Hitec metal gears are designed to attach directly to the output spline of a servo. All gears are broached directly into the metal to ensure a snug fit that will not slip. These gears are designed to fit the standard 24 tooth Hitec output spline.

Specifications:

• Number of teeth: 12
• Diametral pitch: 32
• Pitch diameter: .375
• Face width: 0.250"
• Bore: 24T Servo Spline
• Weight: 0.008

This 12 tooth pinion gear is designed to fit onto an AndyMark RedLine Motor (am-3775) and other motors with a 5 mm output shaft to interface with spur gearboxes such as the DeCIMate (am-3745), EVO Slim for RedLine and EVO Shifter for RedLine. 

Specifications:

• Bore: 5mm press fit
• Weight: 0.014 Pounds
• Material: 1117 Steel
• Overall Length: 0.755 in.
• Face Width: 0.625 in.
• Tooth Count: 12
• Pitch Diameter: 0.375 in.
• Pressure Angle: 20
• Diametral Pitch: 32

This gear comes standard as the pinion for the NeveRest motor, am-3104 

Specifications:

• Module: 0.5
• Tooth Count: 12
• Pressure Angle: 20 Degrees
• Helix Angle: 18 Degrees, Left
• Bore: 2.98mm

The Studica 12V 3,000 mAh NiMH (nickel metal hydride) Battery Pack, PP45 comes with a w/20 amp fuse. It is a 10-cell, 12-volt rechargeable battery that brings long-lasting power to motors and electronics that are used in the WorldSkills Mobile Robotics Collection. The Studica NiMH Battery Pack Charger, PP45, is required to charge the battery.

This battery is NOT COMPETITION LEGAL for FIRST TECH CHALLENGE or FIRST ROBOTICS COMPETITION.

Specifications,

• Dimmensions: 5 x 2.1 x 2.1 inches (115 mm x 45 mm x 50 mm)
• Weight: 1.32lbs (579 g)
• Built-in 20-amp replaceable fuse for safety
• 10-cell pack provides 3,000-mAh capacity for longer life
• PP45 connector for easy and safe connection to controller
• Step File

Specifications:

• Material: 6061-T6 Aluminum
• Number of teeth: 13
• Step File

The 135 Degree Bracket is perfect for connecting two channels pieces at 45 degrees from each other. Each side is 48mm wide to fit perfectly on the channel. Used for intake systems, elevator systems, or structure where 45 degrees is required. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.

Specifications:

• Material - Anodized 6061-T6 Aluminum
• Thickness - 3mm
• Step File

1.420 inch long spacer, with 3/8" nominal id (0.42 actual), made from 3/8" schedule 80 gray PVC pipe 

Specifications:

• Material: 3/8 inch schedule 80 PVC pipe
• Inside diameter: 0.42 inch
• Outside diameter: 0.68 inch
• Length: 1.420 inch
• Weight: 0.02 pounds

Specifications:

• Tooth Count: 14
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 0.7
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex
• Weight: 0.029 Lbs

This is the 14 tooth gear in the Toughbox which has a 3/8 inch hex bore. 

Specifications:

• Number of teeth: 14
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Pitch Diameter: 0.7 inch
• Face width: 0.575 inch
• Overall width: 0.600 inch
• Bore: 0.377 inch hex hole
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.1 lbs.

This is a 15 Degree Bracket used in the Ramp.

Specifications:

• Thickness: 0.09"
• Width: 1.0"
• Hole Size: 0.128"
• Material: 5052 Aluminum