144mm Angle Beam features structural pieces with 90º angles and heavy-duty aluminum construction. Can be cut to custom lengths with a metal-cutting blade.

• Quantity: pkg of 2
• Material: 7005 Aluminum

This encoder is a magnetic rotary encoder that communicates over a robots' CAN bus. This encoder supports CAN 2.0 and provides the same position, velocity, and resolution as you would expect from the SRX Mag encoder.

For Cross The Road Electronics warranty replacements or assistance with CTRE products, please contact Cross The Road Electronics. Email: [email protected]

Specifications

• Current: 60 mA Max, Less than 50 mA Nominal
• Gauge: Minimum Recommended 22 AWG
• Voltage: 6-16V DC

The inside black portion of this wheel is made from molded polycarbonate plastic. The outer tread is TPU (Thermoplastic PolyUrethane). This robust but lightweight wheel provides good traction on carpet and soft tiles. Stealth wheels are the perfect drive wheel for smaller (<50 lb.) robots, or for intakes and other auxiliary robot mechanisms. These wheels are available in a variety of bores and durometers. 3 in. and 4 in. Stealth Wheels feature a 6 bolt pattern on a 1.875 in. bolt circle for mounting sprockets, hubs, and gears. Nub Bore Stealth Wheels feature a 4 bolt pattern on a 16 mm bolt circle found in most FIRST Tech Challenge building systems. The lower the durometer the softer the wheel is, this makes it wear away faster, but also makes it more grippy.

Keep your robots rolling! Use this as a replacement or an extra charger for the 6 V NiMH battery pack that comes with Tetrix Prime; sets.

This 12V flexible color-changing LED strip is perfect for robot lighting whether it's for fun or feedback. When used with an RGB controller such as the roboRIO (sold separately) one can control the color output including solid colors (red, green, blue, etc.) gradient fading, and blinking. Each LED is individually addressable, allowing for the display of multiple colors simultaneously. This light strip features a signal break-point continuous transmission, meaning that when one LED gets damaged, the others will keep working. It accepts 5V or 6V data input and is compatible with our 4pin LED Connector.

NOTE: This strip's color pattern is actually GRB, rather than RGB. When controlling it, you may have to flip the values of red and green to produce the desired color.

The inside black portion of this wheel is made from molded polycarbonate plastic. The outer tread is TPU (Thermoplastic PolyUrethane). This robust but lightweight wheel provides good traction on carpet and soft tiles. Stealth wheels are the perfect drive wheel for smaller (<50 lb.) robots, or for intakes and other auxiliary robot mechanisms. These wheels are available in a variety of bores and durometers. 3 in. and 4 in. Stealth Wheels feature a 6 bolt pattern on a 1.875 in. bolt circle for mounting sprockets, hubs, and gears. Nub Bore Stealth Wheels feature a 4 bolt pattern on a 16 mm bolt circle found in most FIRST Tech Challenge building systems. The lower the durometer the softer the wheel is, this makes it wear away faster, but also makes it more grippy.

TETRIX MAX Flat Building Plates are 64 mm x 192 mm and made of heavy-duty aluminum. Can be cut to custom lengths with a metal-cutting blade.

• Size: 64 mm x 192 mm
• Quantity: pkg of 2
• Material: 7005 Aluminum

Tetrix Prime JR Switch On/Off controls the power between the battery pack and the receiver. 

• Note: Use with the Tetrix Prime; 6 V Battery Pack and Receiver, sold separately
• Weight: 8.5 grams per switch

This is a solderless, clamping connector is intended to be used with our 12V Addressable LED Light Strip. To use, simply cut off some of the clear insulation on the LED strip to reveal the gold contacts, insert into the connector, and pinch to close. The connector will pierce each contact, providing a robust and long lasting connection. The wires on the other side can be swapped around by prying up that side of the connector and simply sliding out each wire and sliding them back in to the desired channels. That way you can keep your power & ground colors consistent and remove the redundant data line if you choose not to use it!

80MM Tube is both light and strong. TETRIX Tubes can be used as long extensions. Made of heavy-duty aluminum, they can also be cut to custom lengths with a metal-cutting blade.

• Length: 80 mm
• Outside Diameter: 15.7 mm
• Quantity: pkg of 2
• Material: 7005 Aluminum

The inside black portion of this wheel is made from molded polycarbonate plastic. The outer tread is TPU (Thermoplastic PolyUrethane). This robust but lightweight wheel provides good traction on carpet and soft tiles. Stealth wheels are the perfect drive wheel for smaller (<50 lb.) robots, or for intakes and other auxiliary robot mechanisms. These wheels are available in a variety of bores and durometers. 3 in. and 4 in. Stealth Wheels feature a 6 bolt pattern on a 1.875 in. bolt circle for mounting sprockets, hubs, and gears. Nub Bore Stealth Wheels feature a 4 bolt pattern on a 16 mm bolt circle found in most FIRST Tech Challenge building systems. The lower the durometer the softer the wheel is, this makes it wear away faster, but also makes it more grippy.

Tetrix Prime 6-32 Socket Head Cap Screws 5/16" secure rotating axle-mounted elements in place. Requires 7/64" hex driver included in Starter Set. 

• Weight: 0.9 grams per screw
• Quantity: pkg of 25
• Size: 6-32
• Length: 5/16"

145MM Tube Pack is light and strong with tubes that can be used as long extensions. Made of heavy-duty aluminum, they can also be cut to custom lengths with a metal-cutting blade.

• Length: 145 mm
• Outside Diameter: 15.7 mm
• Quantity: pkg of 2
• Material: 7005 Aluminum

The inside black portion of this wheel is made from molded polycarbonate plastic. The outer tread is TPU (Thermoplastic PolyUrethane). This robust but lightweight wheel provides good traction on carpet and soft tiles. Stealth wheels are the perfect drive wheel for smaller (<50 lb.) robots, or for intakes and other auxiliary robot mechanisms. These wheels are available in a variety of bores and durometers. 3 in. and 4 in. Stealth Wheels feature a 6 bolt pattern on a 1.875 in. bolt circle for mounting sprockets, hubs, and gears. Nub Bore Stealth Wheels feature a 4 bolt pattern on a 16 mm bolt circle found in most FIRST Tech Challenge building systems. The lower the durometer the softer the wheel is, this makes it wear away faster, but also makes it more grippy.

Great for when you’ve bought extra Tetrix Prime; parts and want uniform bins to store them in. Includes 11-1/8" x 17" lid.